Issue with VM network dropping in and out

glenlewis09

Sorry about that, I am rare to use any forums. Normally I can figure these small issues out myself.

All of my host are running XCP-ng 8.2.1
XEN Orchestra 5.90.0

The Geekom A5 hosts are (4 Hosts):
CPU: AMD Ryzen 7 5800H (8 Cores, 16 Threads, 16MB Cache, 3.2 GHz~ 4.4 GHz)
RAM: Dual-channel DDR4-3200 SODIMM, 64GB
NIC: Realtek 2.5 GB

I also have 4 BeeLink Host running:
CPU: AMD Ryzen 7 5800H (8 Cores, 16 Threads, 16MB Cache, 3.2 GHz~ 4.4 GHz)
RAM: Dual-channel DDR4-3200 SODIMM, 64GB
NIC: 1.0 GB Nic

The VM's running on the Beelink host never have any issue.
a) I only dislike that 1 GB nic so I looked for a new Mini PC with a built in 2.5GB
When I migrate a VM to the Host running on the Geekom PC's the VM becomes unstable with the network connection.
a) I can go through XEN and pull up the console just fine and work with the Desktop UI.
b) When I RDP into the VM the RDP connections drops every couple of seconds and reestablishes quickly.
c) My SQL and IIS services are unable to maintain a connection to each other while on the new Hosts
d) Oddly enough my old laptop I converted to a VM works fine on either set of host. It is running Windows 11 .
The VM's are mostly windows server 2019 and 2022.
All the VM's have the PV drivers installed so the XEN can easily manage them.
a) Management agent 9.3.2-110
All 8 of my host share a NFS storage back to a TrueNas Core

To make sure the issue wasn't the network I completely swapped out all patch cables and the switch the host where connected too, even change the uplink ports just incase.

My first thought was network issue with the HW, but when I connected the original Beelink's to the same ports and cables and no issue I realized it has to be an issue on the host itself.

I would love to figure this one out, since the Geekom have 2.5 GB Nic's I can get better bandwidth for the disk speeds and better overall performance.

Thanks again.

Andrew

@glenlewis09 Does the XCP host report the ethernet link going down? dmesg

glenlewis09

I don't see any logs from the XEN Orchestra.

Home -> Hosts -> GLS-XENHOST08 -> Logs
I see no logs here, Also When I go to Network The status is always showing connected.

Andrew

@glenlewis09 You need to ssh into the XCP host.

glenlewis09

@Andrew

I have found the ssh command to create the log using the xen-bugtool.

I am not a linux guru so I don't know how to transfer the log file from the host to the windows client via ssh. Nor do I know how to access the host files outside of ssh.

[09:14GLS-XENHOST08bug-report]# xen-bugtool --yestoall
Warning: '--yestoall' argument provided, will not prompt for individual files.

This application will collate the Xen dmesg output, details of the
hardware configuration of your machine, information about the build of
Xen that you are using, plus, if you allow it, various logs.

The collated information will be saved as a .tar.bz2 for archiving or
sending to a Technical Support Representative.

The logs may contain private information, and if you are at all
worried about that, you should exit now, or you should explicitly
exclude those logs from the archive.

Omitting /dev/shm/metrics/xcp-rrdd-xenpm, size constraint of xcp-rrdd-plugins exceeded
Omitting /dev/shm/metrics/xcp-rrdd-squeezed, size constraint of xcp-rrdd-plugins exceeded
Omitting /dev/shm/metrics/xcp-rrdd-mem_vms, size constraint of xcp-rrdd-plugins exceeded
Omitting /dev/shm/metrics/xcp-rrdd-mem_host, size constraint of xcp-rrdd-plugins exceeded
[01/31/24 09:14:52 CST] Creating output file
[01/31/24 09:14:52 CST] Running commands to collect data
Writing tarball /var/opt/xen/bug-report/bug-report-20240131091452.tar.bz2 successful.
[09:15GLS-XENHOST08bug-report]#

This is the output from the ssh. But again I am not sure how to copy or even open the log data.

Sorry for the lack of experience here.

gskger

@glenlewis09 You can use WinSCP to connect to your host via SSH and browse the filesystem. WinSCP is a file manager and works in a similar way to Windows Explorer. Bonus: there is also a portable version.

john.c

@gskger said in Issue with VM network dropping in and out:

@glenlewis09 You can use WinSCP to connect to your host via SSH and browse the filesystem. WinSCP is a file manager and works in a similar way to Windows Explorer. Bonus: there is also a portable version.

@gskger @glenlewis09 You can also use use scp directly in PowerShell if on a up to date Windows 10 or Windows 11. You will need the SSH Client feature installed (enabled) though and running PowerShell 5 (or later).

glenlewis09

Thank you so much, that is a great insight. Now I have the logs there are 100+ log files. Which file are you wanting me to look at.

gskger

@glenlewis09 Check out the troubleshooting guide on logs in the documentation. @Andrew was talking about the kernel message logs. At the CLI, you could also type dmsg to show the kernel messages since the last boot. You could narrow the result down further with dmesg | grep -i eth.

Andrew

@glenlewis09 I'm running Windows 10 and 11 and it works correctly.

Are you only having problems with Windows 2019 and 2022 ?

Andrew

@glenlewis09 I don't have the same system as you (also XCP 8.3), but I do have r8125 cards and a 2.5G switch. I installed Windows Server 2022 and have no problems keeping a Remote Desktop connection open and watching YouTube videos (with audio)...

I'll have to try it on my AMD system with the r8125 next.

glenlewis09

@gskger said in Issue with VM network dropping in and out:

dmesg | grep -i eth

Last login: Wed Jan 31 09:11:37 2024 from 192.168.20.168
[13:59 GLS-XENHOST08 ~]#  dmesg | grep -i eth
[    1.042384] xen_netfront: Initialising Xen virtual ethernet driver
[    2.735978] r8125 Ethernet controller driver 9.012.03-NAPI-PTP-RSS loaded
[    3.823280] ACPI Error: Method parse/execution failed \_SB.UBTC._DSM, AE_NOT_FOUND (20180810/psparse-516)
[    3.860193] r8125 0000:02:00.0 side-2697-eth0: renamed from eth0
[    5.989957] r8125 0000:02:00.0 eth0: renamed from side-2697-eth0
[    7.086183] eth0: 0xffffc90040540000, 38:f7:cd:c6:d5:82, IRQ 177
[    7.114826] r8125 0000:02:00.0 eth0: registered PHC device on eth0
[    7.114829] r8125 0000:02:00.0 eth0: reset PHC clock
[    7.148004] device eth0 entered promiscuous mode
[    9.927534] r8125: eth0: link up
[133076.658774] NETDEV WATCHDOG: eth0 (r8125): transmit queue 1 timed out
[133076.685550] r8125 0000:02:00.0 eth0: reset PHC clock
[133076.706192] r8125: eth0: link down
[133079.932108] r8125: eth0: link up
[13:59GLS-XENHOST08~]#

These are the logs for the NIC

glenlewis09

@Andrew

It happens across all Windows OS, WIN 11/ Server 2016/2019/2022

But on one of the VM it never has issue.

But if I move the VM back to the other Host with the 1GB nic all the VM behave correctly.

Thank you.

gskger

@glenlewis09 Just to get more information on the NIC in your system, can you first identify the NICs with lspci | grep Ethernet (returns the ID 00:1f.6 on my system)

# lspci | grep Ethernet
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (11) I219-LM

and than get more details with lspci -s 00:1f.6 -vv using the ID of your NIC

# lspci -s 00:1f.6 -vv
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (11) I219-LM
        Subsystem: Hewlett-Packard Company Device 8715
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 212
        Region 0: Memory at e1200000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [c8] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee00f98  Data: 0000
        Kernel driver in use: e1000e
        Kernel modules: e1000e

While this does not address your issue, it gives more insight into your setup.

Edit: some typos

glenlewis09

@gskger [14:39 GLS-XENHOST08 ~]#  lspci | grep Ethernet
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)
[14:39 GLS-XENHOST08 ~]# ^C
[14:39 GLS-XENHOST08 ~]# lspci -s 02:00.0 -vvv
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)
        Subsystem: Realtek Semiconductor Co., Ltd. Device 0123
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 36
        Region 0: I/O ports at f000 [size=256]
        Region 2: Memory at fce00000 (64-bit, non-prefetchable) [size=64K]
        Region 4: Memory at fce10000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [70] Express (v2) Endpoint, MSI 01
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75.000W
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 256 bytes, MaxReadReq 2048 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
                        ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+
                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via message/WAKE#
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
                LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [b0] MSI-X: Enable+ Count=32 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00000800
        Capabilities: [d0] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Input/output error
                Not readable
        Capabilities: [100 v2] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [148 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Capabilities: [168 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
        Capabilities: [178 v1] Transaction Processing Hints
                No steering table available
        Capabilities: [204 v1] Latency Tolerance Reporting
                Max snoop latency: 1048576ns
                Max no snoop latency: 1048576ns
        Capabilities: [20c v1] L1 PM Substates
                L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
                          PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
        Capabilities: [21c v1] Vendor Specific Information: ID=0002 Rev=4 Len=100 <?>
        Kernel driver in use: r8125
        Kernel modules: r8125

[14:40GLS-XENHOST08~]#

gskger

@glenlewis09 Can you please edit your post and format the output as code (insert ``` before and after the output)? This improves readability.

glenlewis09

@gskger done, thank you for the correction.

gskger

@glenlewis09 Again just to double check: your XCP-ng 8.2.1 is fully up-to-date (yum update returns No packages marked for update)? The refreshed 8.2.1 ISO from December 2023 contained updated drivers contributed by @Andrew, including the r8125 driver.

glenlewis09

@gskger said in Issue with VM network dropping in and out:

yum update

[15:25 GLS-XENHOST08 ~]# yum update
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
Excluding mirror: updates.xcp-ng.org
 * xcp-ng-base: mirrors.xcp-ng.org
Excluding mirror: updates.xcp-ng.org
 * xcp-ng-updates: mirrors.xcp-ng.org
No packages marked for update
[15:25GLS-XENHOST08~]#

gskger

@glenlewis09 The only thing that realy stands out is this error message:

pcilib: sysfs_read_vpd: read failed: Input/output error
                Not readable

Can you please try dmesg | grep VPD and report the output (if any)?