Strange issue with booting XCP-NG

[A Former User]

@danp Aha then it should boot without problems though... Strange...

[Danp]

@appollonius I don't have this issue. Just been following along on this thread and happened to run across the Citrix issue I posted earlier.

[A Former User]

@danp Ahh I thought you had the same problem, but I still find it strange and I cannot find anything about it on the interwebs...

[Danp]

@appollonius Did you read the issue I linked above?

[A Former User]

@danp Yeah though it still does not have any solution... Which is sad

[Danp]

@appollonius Found the patch where Citrix backported the fix to XS 7.1 -- https://github.com/xenserver/xen.pg/commit/4629bd92f3d3263da9d7fe304df422e54d56ee56

@r1 @stormi Guessing that they didn't pass this upstream to the Xen folks.

0 committed to xenserver/xen.pg

CA-316240: Fix booting on some platforms without monitor attached

Some platform UEFI firmware doesn't initialize EFI_GRAPHICS_OUTPUT_PROTOCOL
instance if there is no physically attached display present. So trying
to use it will result in NULL pointer dereference even before existing
BootServices.

Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>

[A Former User]

@danp thanks, I might be able to somehow tweak this in the EFI config but not 100% sure. Will check this out asap, otherwise I'll have to leave it to the Xcp-NG team

[A Former User]

@danp So I have another question, do you think that when I install XCP-NG in BIOS mode that this issue wont arise?

Now I know what the problem might be @stormi could this be an UEFI issue rather than an XCP-NG issue?

[r1]

@danp said in Strange issue with booting XCP-NG:

https://github.com/xenserver/xen.pg/commit/4629bd92f3d3263da9d7fe304df422e54d56ee56

This seems present for XCP-ng 8.0 and 8.2..

[A Former User]

@r1 Its still strange though that this problem still persists. As I think there are more people using the Quadro P400.. (Correct me if I'm wrong of course).

[A Former User]

Do you guys think that this has to do with UEFI? Otherwise I will have to reinstall XCP-NG in BIOS mode instead of UEFI mode...

[r1]

@appollonius I don't think it is driver issue (POST boot).. We may know more only from serial output.

Are you able to boot as-is in BIOS mode without reinstall?

[A Former User]

@r1 I could try that, will update when that has been done...

[A Former User]

@r1 How do I boot in BIOS mode without a reinstall? Can that even be done, because I remember that when I installed xcp-ng I had to choose between BIOS or UEFI am I correct? (Could be something else though) otherwise if not I can give that a try.

[r1]

@appollonius I think it will depend on hardware settings. See if you have option to change the mode in motherboard settings?

I don't have physical hardware access to validate this as I mostly use nested virtualization but XCP-ng /boot has required files support both for UEFI and BIOS mode.

Maybe @stormi can confirm.

[A Former User]

@r1 If this could be confirmed I would be happy to test it, otherwise I'll have to do it when I have a new system.. Because I dont want to mess up the current one just yet

[r1]

@appollonius I don't think there is any harm. You will be either be able to boot or not. You can always switch back to old settings.

[A Former User]

@r1 Alright then I will give it a try somewhere today

[stormi]

Unless I'm mistaken, XCP-ng installed in UEFI mode won't boot in bios mode. There won't be anything written in the MBR.

[A Former User]

@stormi Ahh... So I would have to reinstall XCP-NG completely to be able to boot in BIOS?