Congrats on this release! I've done a 'yum update' on a XS 7.5 on a host with a Qlogic fibre channel HBA. It updated to 7.6 and the HBA works as expected. Qlogic management tools are useful if one wants to tweak HBA parameters or update its firmware. They are not needed for everyday usage.
Best posts made by ecoutinho
-
RE: XCP-ng 7.6 beta
-
RE: XCP-ng 8.3 betas and RCs feedback 🚀
@stormi I've upgraded the master in BIOS mode, and proceeded to reinstall one of the other hosts in UEFI mode, after having removed it from the pool. It went fine, until I tried to add the host back into the pool. This was not possible because the reinstalled host has Certificate Verification enabled, while the pool doesn't. Even if I host-emergency-disable-tls-verification, it's not possible to add the server back into the pool.
It seems I'll have to upgrade the other hosts in BIOS mode, enable certificate verification on the pool and then add this host. I guess I'll reinstall the other hosts in UEFI mode on a future upgrade.
Latest posts made by ecoutinho
-
RE: XCP-ng 8.3 betas and RCs feedback 🚀
@stormi OK, thanks, I'll finish upgrading the other hosts.
-
RE: XCP-ng 8.3 betas and RCs feedback 🚀
@stormi Thanks for your suggestions. I've tried to enable it on the pool:
# xe pool-enable-tls-verification This operation is not supported during an upgrade.
I have to finish the upgrade of the other hosts before enabling it on the pool.
As for disabling it on the new host, I didn't find any way to do it permanently. I just found the host-emergency-disable-tls-verification option, which does not disable it completely, and doesn't allow to add it to a pool without TLS verification. Would you clarify how to disable it on the new host?
I will enable it on the pool when the upgrade is finished.
-
RE: XCP-ng 8.3 betas and RCs feedback 🚀
@stormi I've upgraded the master in BIOS mode, and proceeded to reinstall one of the other hosts in UEFI mode, after having removed it from the pool. It went fine, until I tried to add the host back into the pool. This was not possible because the reinstalled host has Certificate Verification enabled, while the pool doesn't. Even if I host-emergency-disable-tls-verification, it's not possible to add the server back into the pool.
It seems I'll have to upgrade the other hosts in BIOS mode, enable certificate verification on the pool and then add this host. I guess I'll reinstall the other hosts in UEFI mode on a future upgrade.
-
RE: XCP-ng 8.3 betas and RCs feedback 🚀
While installing 8.3 RC1 it says BIOS boot mode is deprecated and I should use UEFI. But if I boot in UEFI, when I choose to upgrade the existing installation, an error occurs: "Installer mode (UEFI) is mismatched with target host mode (legacy)".
To be clear, it is not possible to migrate from BIOS mode to UEFI during an upgrade?
In that case, the only option would be to remove the host from the pool, install XCP-ng (not upgrade) and then add it to the pool. Am I correct? Thanks.
-
RE: XCP-ng 7.6 beta
Congrats on this release! I've done a 'yum update' on a XS 7.5 on a host with a Qlogic fibre channel HBA. It updated to 7.6 and the HBA works as expected. Qlogic management tools are useful if one wants to tweak HBA parameters or update its firmware. They are not needed for everyday usage.
-
RE: XCP-ng 7.5.0 Release Candidate
On a test machine, I've upgraded from Xenserver 7.2 directly to this version and it worked fine. I've used PXE network installation to upgrade.
Congrats on this release!