RTL8153 Compile

geant90

Man I am here trying. I got the rules in aswell as the driver selected and loaded. pif-list says no for currently attached?

geant90

How can I get 4.14.78?

Can you send me that r8152.ko v1.09.9

geant90

Got a bit more progress. So it does not work in xCenter gui but looking at ifconfig I have statistic and after assign an ip address got it to respond to ping. It does not make a xenbridge though?

geant90

This post is deleted!

geant90

Looks like it has been working all along just xCenter not showing it correctly.

![0_1541229437535_usbnic.PNG](Uploading 100%)

Where does xCenter pull these stats from?

r1

@geant90 you will need to do a xe pif-scan if the NIC was not present during installation.

Also, please share exact vendor id of your NIC. You can obtain it from lspci -v or dmesg

geant90

I did. I even deleted and reintroduce with mac but no luck. Where does the dash get that information the pif is showing connected in command with the uuid but not in gui.

geant90

@r1 Do you mean the already known 2357:0601?

r1

@geant90 Just wanted to know that you are seeing the same ID 2357:0601.

If #ifconfig shows it correctly and the networking is working fine, you can scan it via XCP-NG-Center or # xe pif-introduce to let XAPI know about it.

Does your #xsconsole show it under "Display NICs"?

geant90

@r1 I did do a scan. It detects it and adds to xcenter but list as disconnected. The console shows it but unknown and not connected. It does operate just fine as is but I would love for it to be as compatible as possible and we are so close.

Various Info

Check out that link.

So Xen scans and detects the usbnic fine. Adds under device but no data is populated. pif-list command shows device is currently attatched. In xCenter I configure an addition network with ip as seen @ .92 and it works fine. When I do a pif-param-list I beleive xCenter gets the info from there. Most of it is missing. ifconfig shows all the right info. If I can somehow find out where does pif get this info I could modify it to call info from ifconfig and whatever else necesarry. After I get this figure out I will also have it always get same interface name.

So far to get this easily working on others it would just need a script that:

copies rules and .ko appropriate places and updates
PLAN: Persistent inf name for xen
3)PLAN: Get pif for device to get the needed info from ifconfig as it has all necesarry data. so it appears as any other NIC. So far it is working as it should

r1

@geant90 I would ping @borzel to see if he knows about this behavior. Your #ifconfig shows correct info, can assign ip and works fine but XCP-NG-Center says its disconnected.
You say #xe pif-* works fine.

XCP-NG-Center gets data from XAPI, the same API used by xe, so it would be a very rare case that the info produced is mismatching.

Can you share screenshot of Host NICs from

XCP-NG-Center
#xsconsole -> Display NICS
#xe pif-param-list

BTW, did you try XOA product, its a web based alternative to XCP-NG-Center with added automated functions?

geant90

@r1

[root@CNP-MOBILE ~]# xe pif-param-list uuid=f4cab341-1f20-d9e6-4164-627debe5f03f
uuid ( RO)                       : f4cab341-1f20-d9e6-4164-627debe5f03f
                     device ( RO): side-373-eth0
                        MAC ( RO): 50:3e:aa:85:a7:ac
                   physical ( RO): true
                    managed ( RO): true
         currently-attached ( RO): true
                        MTU ( RO): 1500
                       VLAN ( RO): -1
             bond-master-of ( RO):
              bond-slave-of ( RO): <not in database>
      sriov-physical-PIF-of ( RO):
       sriov-logical-PIF-of ( RO):
       tunnel-access-PIF-of ( RO):
    tunnel-transport-PIF-of ( RO):
                 management ( RO): false
               network-uuid ( RO): 4f2d9638-59ae-6ce7-b36d-fea5eeb13d01
         network-name-label ( RO): Pool-wide network associated with side-373-eth0
                  host-uuid ( RO): af183f35-2629-4472-9538-90c2b37dca85
            host-name-label ( RO): CNP-MOBILE
      IP-configuration-mode ( RO): Static
                         IP ( RO): 192.168.91.92
                    netmask ( RO): 255.255.255.0
                    gateway ( RO): 192.168.91.1
    IPv6-configuration-mode ( RO): None
                       IPv6 ( RO):
               IPv6-gateway ( RO):
       primary-address-type ( RO): IPv4
                        DNS ( RO):
                 properties (MRO): gro: on
               capabilities (SRO):
                io_read_kbs ( RO): <unknown>
               io_write_kbs ( RO): <unknown>
                    carrier ( RO): false
                  vendor-id ( RO):
                vendor-name ( RO):
                  device-id ( RO):
                device-name ( RO):
                      speed ( RO): 0 Mbit/s
                     duplex ( RO): unknown
            disallow-unplug ( RW): false
               pci-bus-path ( RO):
               other-config (MRW): management_purpose: Extra
       igmp-snooping-status ( RO): disabled

Heres the picture of NIC
xscone Display + xcenter

I know about XOA, use it at work. For this test machine I built a fresh XenServer 7.6 As I hope to get it working as natural as possible. That way if it works in XS it'll work in XCP-NG and XOA. As again goal is so it works for everywhere after a script shell install.
Do you happen to have a usb nic woring in xen? Screen shots for comparison?

r1

@geant90 so its XAPI itself that does not recognize the interface being online.

Whats the #ethtool -i ethX and ethtool ethX output look like?

Usually on pif-scan the interface (if online) should get registered. And does #dmesg shows that interface is now online when you plug a LAN into it?

geant90

@r1

[root@CNP-MOBILE ~]# ethtool -i side-373-eth0
driver: r8152
version: v2.10.00 (2018/03/16)
firmware-version:
bus-info: usb-0000:00:14.0-1
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no

[root@CNP-MOBILE ~]# ethtool side-373-eth0
Settings for side-373-eth0:
        Supported ports: [ MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supported pause frame use: No
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Half 1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 32
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00007fff (32767)
                               drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol
        Link detected: yes
[root@CNP-MOBILE ~]#

Hmm just noticed for my other interface that works fine where it says Ports for the result of #ethtool under the USB#Gig NIC it says MII and the other working NIC says Twisted pair!?!? I know what a MII but could it be that? Anyone has working media interface to rule that out?

r1

Ah! You will have to do a #interface-rename operation to rename your side-373-eth0 to eth1, then XAPI will recognize it. Can you try it, I don't have exact command around but you can check with its help or code.

geant90

@r1

Man that is exactly what I was thinking about 4-5 hours ago driving to work. I was thinking maybe it has something to do with Xserver only recognizing calling NIC names "ethx" The only reason I had not tried it was because I wanted to ensure functionality before renaming to something persistent. Will keep you posted. Because it does pull the same stats matching from my function NIC. Will attempt after lunch!

geant90

@r1 @borzel

Ladies and gentlemen we have struck gold.

[root@XenServer-TestNIC ~]# interface-rename --list
ERROR    [2018-11-05 12:36:24] Can't generate current state for interface '{'Driver': 'r8152', 'Permanent MAC': '50:3E:AA:85:B6:AE', 'Bus Info': 'usb-0000:00:14.0-2', 'BIOS device': {'all_ethN': 'eth1', 'physical': ''}, 'Assigned MAC': '50:3E:AA:85:B6:AE', 'Firmware version': '', 'Driver version': 'v2.10.00 (2018/03/16)', 'Kernel name': 'side-9065-eth1'}' - Unrecognised PCI address 'usb-0000:00:14.0-2'
Name  MAC                PCI              ethN  Phys  SMBios       Driver  Version       Firmware
eth0  a0:d3:c1:06:ed:a1  0000:00:19.0[0]  eth0  em1   Onboard LAN  e1000e  3.4.0.2-NAPI  0.13-4
[root@XenServer-TestNIC ~]#

So it looks like it has a problem being a usb device. Time to find out what can be done to over come this.

Unrecognised PCI address 'usb-0000:00:14.0-2'

olivierlambert

Yayy! It's more clear. The rename script is probably only looking for PCI device, not USB one. Now, we'll have to find where this code is written and improve it

r1

@geant90 awesome I'm sure the relevant team shall bring a resolution.

stormi

Here's the source: https://github.com/xcp-ng-rpms/interface-rename