XCP-ng 8.2 updates announcements and testing

borzel

@stormi testhost updated, restored some part of our infrastructur (DC, Mail, ...) on local ZFS pool, connected the VMs to a test network. Runs. A bit slow (more vCPU used than the PCPU can delivier), but runs.

rizaemet 0

@stormi said in Updates announcements and testing:

Anyone?

I updated one host in a pool and reboot. It is working as before. Seems no problem. I can't see any diffrence vcpu usage as @borzel say.

AllooTikeeChaat

So far so good .. I haven't noticed any visible change in performance like @borzel but still monitoring.

stormi

Since there's an update for both XCP-ng 7.5 and 7.6, please all tell me which version you tested

borzel

@AllooTikeeChaat there was no performance change, was the first use of that test host

@stormi XCP-ng 7.6, just HVM, no PV

stormi

If all goes well I'll push the updates to everyone on monday. Meanwhile, please go on with the testing if you can.

rizaemet 0

@stormi XCP-ng 7.6

stormi

Thanks to everyone who tested the update candidate. I've now pushed the security update for XCP-ng 7.6. I'm holding that of XCP-ng 7.5 until at least one person confirms that it's working for them.

AllooTikeeChaat

Sorry been away this weekend .. @stormi XCP-ng 7.6

Ultra2D

I've installed the updates on a pool. Now every time I migrate a pfSense HVM VM within the pool the console is gone and memory usage is at 100%. I did do the following on the pool master: yum update xenopsd xenopsd-xc xenopsd-xenlight --enablerepo='xcp-ng-updates_testing'. The package version also differs from other hosts (0.66.0-1.1.xcpng versus 0.66.0-1.el7.centos). Would that be the cause?

stormi

@Ultra2D Could you downgrade to the previous version with yum downgrade xenopsd xenopsd-xc xenopsd-xenlight, restart the toolstack and tell us if migration works better?

Also make sure that you already have the latest updates for xcp-emu-manager, which fixed many migration issues about two months ago. See https://github.com/xcp-ng/xcp/wiki/Updates-Howto#a-special-word-about-xcp-ng-75-76-and-live-migrations.

stormi

@Ultra2D In fact, you may be right, differing versions of those packages may cause an issue, because both hosts may behave differently regarding VMs that have no platform:device-id set.

So another test to do would be install the update candidate for those packages on all hosts and restart their toolstack, then test migration of that VM again.

Ultra2D

@stormi Thanks. Installing the update candidate on all hosts and restarting the toolstack works, but only after power cycling the VM once.
xcp-emu-manager is version 0.0.9-1

Is it advisable to stay on the testing repo until the next version? There are some more non-Windows HVM VM's.

stormi

@Ultra2D so you mean that installing the updated packages would "break" the first migration of such a VM unless it's been rebooted once? If that is so, then I'd advise to revert to the previous version (or to make sure not to attempt a migration without power cycling the VMs once). Else, your choice. If the updated packages bring a benefit to you, you can keep them, else revert to the previous ones.

Ultra2D

@stormi I only tested with one VM. It crashed a couple of times when the pool master had updates from xcp-ng-updates_testing and the slaves had the updates that were released yesterday. After updating the last remaining slave to updates from xcp-ng-updates_testing, moving the VM resulted in a stuck VM. So I don't think you can draw any conclusions from this, except maybe that you should install the same version on master and slaves.

stormi

Xen security updates pushed to everyone (7.6 yesterday, 7.5 today).
Blog post: https://xcp-ng.org/blog/2019/03/12/xcp-ng-security-bulletin-vulnerabilities-pv-guests/

codedmind

I'm getting an error


Running transaction test


Transaction check error:
  installing package xen-dom0-tools-4.7.6-6.4.1.xcpng.x86_64 needs 1 inodes on the /var/log filesystem

stormi

@codedmind This is probably related to a bug in the openvswitch package and log rotation. We sent a newsletter about it a few days ago: https://mailchi.mp/7ed52f9a2151/important-noticeopenvswitch-issue

codedmind

Humm ok... but i cannot update... yes i have that version.. but as i cannot up date how can i solve it?

stormi

@codedmind when it got to the point that you ran out of inodes in /var/log, you need to remove some files before you can update. find /var/log -name ovsdb-server.log.*.gz -delete should work (untested, try without -delete first). Else look at the other threads that covered the subject.