RTL8153 Compile

geant90

Anyone knows where is the database for USB vendors and product ids? Would like to put an edit in there to see if that would generate proper info.

geant90

@olivierlambert @r1 @stormi

Any one knows the file location for usb vendor and product ID?

Nevermind found it!

geant90

Got it showing in lsusb properly now time to figure xapi

[root@CNP-MOBILE ~]# xe pif-param-list uuid=9212a2c9-b68c-9ac6-cb76-d9baa6af2c5e
uuid ( RO)                       : 9212a2c9-b68c-9ac6-cb76-d9baa6af2c5e
                     device ( RO): eth10
                        MAC ( RO): 50:3e:aa:85:b6:ae
                   physical ( RO): true
                    managed ( RO): true
         currently-attached ( RO): false
                        MTU ( RO): 1500
                       VLAN ( RO): -1
             bond-master-of ( RO):
              bond-slave-of ( RO): <not in database>
      sriov-physical-PIF-of ( RO):
       sriov-logical-PIF-of ( RO):
       tunnel-access-PIF-of ( RO):
    tunnel-transport-PIF-of ( RO):
                 management ( RO): false
               network-uuid ( RO): 4a3277cb-f48b-47cc-ba69-7d73f02d814f
         network-name-label ( RO): Pool-wide network associated with eth10
                  host-uuid ( RO): af183f35-2629-4472-9538-90c2b37dca85
            host-name-label ( RO): CNP-MOBILE
      IP-configuration-mode ( RO): None
                         IP ( RO):
                    netmask ( RO):
                    gateway ( RO):
    IPv6-configuration-mode ( RO): None
                       IPv6 ( RO):
               IPv6-gateway ( RO):
       primary-address-type ( RO): IPv4
                        DNS ( RO):
                 properties (MRO): gro: on
               capabilities (SRO):
                io_read_kbs ( RO): 0.000
               io_write_kbs ( RO): 0.000
                    carrier ( RO): false
                  vendor-id ( RO):
                vendor-name ( RO):
                  device-id ( RO):
                device-name ( RO):
                      speed ( RO): 0 Mbit/s
                     duplex ( RO): unknown
            disallow-unplug ( RW): false
               pci-bus-path ( RO): 2-1:1.0
               other-config (MRW):
       igmp-snooping-status ( RO): unknown


[root@CNP-MOBILE ~]# lsusb
Bus 002 Device 002: ID 2357:0601 TP-LINK USB 10/100/1000 LAN
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
[root@CNP-MOBILE ~]#

olivierlambert

Okay great Can you share with us all the modification you had to made? What can we do to have this integrated in XCP-ng? (ie not a too specific code ideally that would work with other network USB devices)

Thanks!

geant90

@olivierlambert

Of course. Right now I just got enough information to start the modification on the script which I start tomorrow. In fact, all that is needed to get usbnics working properly in xapi is simply being able to identify usb locations. THAT'S IT! All NICs if you look in the logs are initially named side then because the rename script runs and after properly identifying it assigns a ethxx name which the api will work with. All this would take is an import command and a few if commands. I got the logic down so now it is just about editing, trial and error.

Question regarding:

import sys, logging
from optparse import OptionParser, OptionGroup
from os.path import join as joinpath, normpath, exists as pathexists
from subprocess import Popen

try:
    import cStringIO as StringIO
except ImportError:
    import StringIO

import xcp.logger as LOG
from xcp.pci import PCI
from xcp.net.biosdevname import all_devices_all_names
from xcp.net.ip import ip_link_set_name
from xcp.net.ifrename.logic import rename
from xcp.net.ifrename.macpci import MACPCI
from xcp.net.ifrename.static import StaticRules
from xcp.net.ifrename.dynamic import DynamicRules
from xcp.net.ifrename.util import niceformat
from xcp.net.mac import MAC

for the import command as my google fu was no help for the above xcp.net and xcp.pci what is it specifically referring to?
What I have that down we simply need to add and import for usb then modify a few existing calls with the first being if device location = usb format then run the modify version of the script that would have the edited fields to pull the proper usb locations etc. For the vendor and device it would be best and most simple if we refer to the usbvidpid list it can simply call the info from an already large existing database which can also be easily updated and/or modified for an entry. Functionality wise all that is needed is those if commands to make a usb location referable. Then any usb NIC (so long as drivers provided) would be truly plug and play and we could use the existing config to chose a specific ethxx name based on MAC so they survive reboots without further editing anything.

Got it is referring to the python libary / libs

BillyC

Has there been any more work on this? I'm testing XCP-NG 8 beta and was hoping to try and test out similar usb nic?

Peek

This post is deleted!

Peek

This post is deleted!

Peek

Here's another willing script tester

Pen2

has enyone get this usb nic to work?

r1

@Pen2 I think most people have

I think the rename script modification to recognize PCI and USB device was the key.

Professor-X-Tech

@r1 any way you can share how to do it? I have the same issue I’m with the usb 3 Ethernet Adapter I have.

r1

@Professor-X-Tech please go though the thread once and share us the commands used, errors seen.

Professor-X-Tech

@r1

Naming is showing incorrect like others, have reported.

Let me know if you need anything else.

listing and scanning the USB Nic - side-861-eth0

2020-06-26 17_16_38-Clipboard.png

interface-rename -l (Giving an Error.)

xsconsole showing it but not connected

lsusb

dmesg with vendor ID

Pen2

i find patch solution
just make file /etc/udev/rules.d/70-persistent-net.rules
and put your all nic in it like this:

SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="6a:66:e8:33:0f:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="ed:8c:c1:ba:cb:b9", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="7c:3f:5f:fa:e4:a3", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2"

just change your own mac address. reboot and then xe pif-forget=(side-xxx uuid)
and reboot.

Professor-X-Tech

@Pen2 Dude! you the man! lol thanks for this. saving this for the book so I don't forget in case it gets changed some day.

gskger

Don't forget to stop the dynamic NIC naming by adding net.ifnames=0 to the grub boot menu (see this article by Eric Eikrem). Worked for my USB-NIC (Startech, ASIX Electronics Corp. AX88179 USB 3.0 to Gigabit Ethernet) as described in Prevent USB-NIC device renaming - valid approach on xcp-ng?. Not sure if it really is mandatory to add the on-board NIC to the rules file as well, but I do it.

Professor-X-Tech

@gskger I had followed the article by Eric Eikrem and it did not work for me. Base on my understanding if you add the rules it won’t rename it to anything other then what’s in the static rules.

Found this in a RHEL Forum:

https://access.redhat.com/discussions/916973

Professor-X-Tech

@Professor-X-Tech I'm back to report that although it working, I am having issue with the USB 3 Nic. Don't have time to troubleshoot it but I will get to it and if I find anything to share I will.

jokurinopoloski

Quite old topic, but I have been struggling for MONTHS (literally) now and I'm getting stressed in daily life.

I have everything working so far to the point where it is showing in xencenter as a valid nic with 2500mbit full duplex specifications.

using this usb nic: https://www.club-3d.com/en/detail/2467/usb_3.1_gen1_type_a_to_rj45_2.5gbps/

I can ping with it, connect to it with SSH and give the NIC to my windows server VM. The only problem that is holding me back from using this USB nic is that all my windows VM's are getting SSL errors on any internet browser i'm on. Internet just doesn't work.

Besides that I can't even copy files from any VM to my normal PC anymore since it's getting stuck on 0KB/s and eventually crashes my explorer.exe.

Something is really wrong here and man... I must have had every single guide possible in front of me I'm sorry for reviving this thread but i'm getting desperate.

I hope there is someone who can help me maybe through email or this forum. I'm willing to share everything I did to get this working.