-
- use iodepth of 128
- use 4 process at the same time (numjobs=4)
- use io_uring if you can in the guest (and not libaio)
- don't use a test file but bench directly on a non-formatted device (like /dev/xvdb), this removes the filesystem layer
With those settings in
fio
, I can reach near 2600MiB/s in read, and 900MiB/s in write with 4x virtual disks in mdadm RAID0, in the guest (a test VM on Debian 12), on rather "old" Xeon CPUs and a PCIe 3 ports on an consumer grade NVMe SSD.Also, latest thing to know: if you use thin pro, you need to run the test twice, the first run (while the VHD is growing), it's always slower. And this is not a problem in real life, you can run twice or 3 times and check the result your tests, without counting the first.
I'm about to get more recent hardware (except the NVMe) to re-run some tests this week. But as you can see, you can go over a 20G network (I'm using a 25G NIC)
-
@olivierlambert thx for the feedback! I do not get how you see that you reach 20G on your nic. Can you please explain it? I see that you reach 2600MiB/s in read, but this is more likely on local disk, isn't? What I can see in our lab environment is that for what ever reason we do not get more than around 8Gbits on pass-through via a 40G interface and 4Gbits via a 10G interface and therefore we do not get any good performance out of the storage repository. I am unable to find the root cause of this. Do you have any idea where to look? I can see high waits on the OS of the VM, but no waits inside dom0 of any node.
-
First, always do your storage speed test in a regular VM. The Dom0 doesn't matter: you won't run your workload in it, so test what's relevant to you: inside a dedicated VM.
Also, it's not only a matter of network speed, but latency, DRBD, SSD speed any many other things. Only Optane drives or RAM are relevant to really push XOSTOR, because there's not a lot of NVMe that can sustain heavy writes without slowing down (especially on 100GiB file).
But first, start to benchmark with the right
fio
parameters, and let's see -
@olivierlambert just to be sure: we did also use your recommended fio parameters with the exact same results. We used fio from inside a VM not from inside dom0. My comments regarding waits inside the VM and no waits in dom0 was just additional information.
I am aware of possible bottleneck like latency, SSD others, but in our case we can rule them out. Reason is that we double our speed when switching from 10G to 40G interface while the rest is the exact same configuration. As fsr as I can see this looks to me like xcp-ng is the bottleneck and limiting bandwidth of the interface in some way. Even the numbers you provided are not really good performance numbers. Did you get more bandwidth than 8 Gbits over the linstor interface?
We are going to install Ubuntu on the same servers and install linstor on it to test our infrastructure on bare-metal without any hypervisor to see if it is xcp-ng related or not.
-
Those are really good numbers for a replicated block system, on top of a virtualization solution.
The fact you are doubling the speed isn't just about bandwidth, but also likely latency related. XOSTOR works in sync mode, so you have to wait for blocks to be written on the destination before getting the confirmation. You might try on bigger blocks to see if you can reach higher throughput.
Also, remember that if you test in a VM on a single virtual disk, that's absolutely the bottleneck here (
tapdisk
). There's one process per disk, that's why I advise to test either with multiple VMs at the same time to really push XOSTOR to its limits, or create a big RAID0 with many virtual drives you can (however, first option is better because you can have VMs on multiple hosts at the same time).In short, the system scales with the number of VMs, not when benchmarking with one VM and one disk only.
Finally, don't forget thin mode that is requiring to run the test at least twice to really see the performance. On your side, you are very likely CPU bound due to an 8 years old Intel CPU/architecture, which is not that's efficient. But on that, I'll be able to provide a real result comparing my test bench in Xeon vs Zen in 2 days.
-
Is it possible to change replication factor later on the fly eg. after adding a new host (without loosing data) ?
-
That's a question for @ronan-a when he'll be back
But in any case, IIRC, the preferred replication number for now is 2.
-
@gb-123 You can use this command:
linstor resource-group modify xcp-sr-linstor_group_thin_device --place-count <NEW_COUNT>
You can confirm the resource group to use with:
linstor resource-group list
Ignore the default group named:
DfltRscGrp
and take the second.Note: Don't use a replication count greater than 3.
-
I have installed the XOSTOR with replica count of 2.
I have tried running one E-mail Server (PostFix) and one Web-Server (Nginx), with their VHD on XOSTOR. They seem to run fine. I have not done any benchmarks for now.After installing, I noticed that the VxLAN (Encrypted) has stopped working.
Update:
I managed to fix the VxLAN by :
- Completely Removing all PIFs of VxLAN and removing the VxLAN Network from the pool
- Remove SDN controller configuration from plugin page > delete configuation
- Shutdown ALL hosts from the pool
- Restart XO VM
- Enable SDN controller again (this time with Override Certs ON)
- Click Save Configuration.
- Start All Hosts
- Create VxLAN again.
Previous Error Details (Now Solved as mentioned in the update above):
So this is how I was using:
1 VM on Node 1 which runs pfSense Router
VxLan (encrypted) on the pool.Other VMs on Node 1 & Node 2.
VMs on Node1 are connecting to the pfSense which is running on the same node.
VMs on Node2 have stopped connecting.I have not changed any settings. All I did for installing XOSTOR, was remove the previous SR (after migrating vhd to another sr using XO) edit partition (using fdisk) and then create 2 SRs (One for EXT4 and the Other for XOSTOR) and migrate all VHDs back to EXT4 and XOSTOR (as per requirement). I did this for both nodes.
I am not sure if installing XOSTOR has something to do with this or not so this is not a bug report (yet).So far I have tried :
- Turn off and turn on SDN Controller in XO
- Override certificates in SDN controller in XO and rebooting both host nodes.
Do you think XOSTOR would have an impact on the MTU in the host Network Card ?
Any direction you can give me to diagnose the problem ?
I am planning to remove the VxLAN and re-create it. Do you think it would help ?Update : Checked XO Logs:
I get :2023-08-11T14:00:17.907Z xo:xo-server:sdn-controller:tls-connect ERROR TLS connection failed { xen-orchestra-docker-orchestra-1 | error: [Error: 58EBD01E7F7F0000:error:0A000418:SSL routines:ssl3_read_bytes:tlsv1 alert unknown ca:../deps/openssl/openssl/ssl/record/rec_layer_s3.c:1586:SSL alert number 48] { | library: 'SSL routines', | reason: 'tlsv1 alert unknown ca', | code: 'ERR_SSL_TLSV1_ALERT_UNKNOWN_CA' | },
Though earlier, the connection between Node1 and Node 2 were still being made despite this warning. So this is not new.
Further Update:
I deleted the previous VxLAN and now when I try to create it, it gives me the following error :
sdnController.createPrivateNetwork { "poolIds": [ "b990a09e(*removed*)" ], "pifIds": [ "68fc6193(*removed*)" ], "name": "VxLAN", "description": "Private Lan Network", "encapsulation": "vxlan", "encrypted": true, "mtu": 1500 } { "library": "SSL routines", "reason": "tlsv1 alert unknown ca", "code": "ERR_SSL_TLSV1_ALERT_UNKNOWN_CA", "message": "582B645BC47F0000:error:0A000418:SSL routines:ssl3_read_bytes:tlsv1 alert unknown ca:../deps/openssl/openssl/ssl/record/rec_layer_s3.c:1586:SSL alert number 48 ", "name": "Error", "stack": "Error: 582B645BC47F0000:error:0A000418:SSL routines:ssl3_read_bytes:tlsv1 alert unknown ca:../deps/openssl/openssl/ssl/record/rec_layer_s3.c:1586:SSL alert number 48 " }
-
running linstor command on both hosts gives the following error :
Traceback (most recent call last): File "/usr/bin/linstor", line 21, in <module> import linstor_client_main ImportError: No module named linstor_client_main
-
@olivierlambert did you already had the change to test your new hardware?
We did some more benchmarking with only bonded 40G interface.
We used the following fio command:
fio --name=a --direct=1 --bs=1M --iodepth=32 --ioengine=libaio --rw=write- on bare-metal (OS: Ubuntu 22 LTS) we are able to reach 3100MB/s
- on a VM installed on xcp-ng we are able to reach 1200MB/s
- on dom0 we are able to reach 1300MB/s when create a new linstor volume and using /dev/drbd directly
- on dom0 when using the lvm without drbd we are able to reach 1500MB/s
And btw it looks like tapdisk is our bottleneck on dom0 as you suggested before, because this is a single-thread process and our CPU reached a limit.
From the numbers above the performance inside the VM does not look as bad as we thought at the beginning. The only question we have at this moment is why we are "loosing" over half of the performance between a bare-metal installation and when testing the same storage from within dom0?
Is this expected behavior? -
This post is deleted! -
@Swen Yes, it is expected. The Dom0 is NOT the baremetal but a VM in PV mode. Also, it doesn't have all the resources of the host (as a VM, only a fraction of CPUs/memory, but also not -for now- a recent kernel and IO uring.
-
@gb-123 said in XOSTOR hyperconvergence preview:
running linstor command on both hosts gives the following error :
Traceback (most recent call last):
File "/usr/bin/linstor", line 21, in <module>
import linstor_client_main
ImportError: No module named linstor_client_mainRegarding this error, can you say me what's your XCP-ng version? And what's the output of:
yum list installed | grep -i linstor
? Do you have a XCP-ng 8.3? And did you run the beta installation script on it?Also, your SSL/VLAN issue is not caused by LINSTOR, @BenjiReis do you have any idea?
-
@ronan-a said in XOSTOR hyperconvergence preview:
@gb-123 said in XOSTOR hyperconvergence preview:
running linstor command on both hosts gives the following error :
Traceback (most recent call last):
File "/usr/bin/linstor", line 21, in <module>
import linstor_client_main
ImportError: No module named linstor_client_mainRegarding this error, can you say me what's your XCP-ng version? And what's the output of:
yum list installed | grep -i linstor
?Output of
yum list installed | grep -i linstor
:drbd.x86_64 9.22.0-1.el7 @xcp-ng-linstor drbd-bash-completion.x86_64 9.22.0-1.el7 @xcp-ng-linstor drbd-pacemaker.x86_64 9.22.0-1.el7 @xcp-ng-linstor drbd-reactor.x86_64 1.0.0-1 @xcp-ng-linstor drbd-udev.x86_64 9.22.0-1.el7 @xcp-ng-linstor drbd-utils.x86_64 9.22.0-1.el7 @xcp-ng-linstor drbd-xen.x86_64 9.22.0-1.el7 @xcp-ng-linstor kmod-drbd.x86_64 9.2.2+ptf.1_4.19.0+1-1 @xcp-ng-linstor linstor-client.noarch 1.18.0-1 @xcp-ng-linstor linstor-common.noarch 1.21.1-1.el7 @xcp-ng-linstor linstor-controller.noarch 1.21.1-1.el7 @xcp-ng-linstor linstor-satellite.noarch 1.21.1-1.el7 @xcp-ng-linstor python-linstor.noarch 1.18.0-1 @xcp-ng-linstor xcp-ng-linstor.noarch 1.2-1.xcpng8.3 @xcp-ng-linstor xcp-ng-release-linstor.noarch 1.4-1.xcpng8.3 @xcp-ng-base
Do you have a XCP-ng 8.3? And did you run the beta installation script on it?
I installed XCP-ng 8.3 beta from ISO and then applied all the patches that were available. To install linstor, I followed the 1st Post of this topic.
Also, your SSL/VLAN issue is not caused by LINSTOR, @BenjiReis do you have any idea?
Yeah, even I thought so, but nothing changed for me before I installed Linstor.
There is also a very peculiar thing I am noticing:
Backup from Thin (Ext4) SR to another Thin (Ext4) SR has a transfer of 120KiBs over network(WAN). I thought this is maybe due to a 'slow' network, but however, I started another backup at the same time while the previous one was running slowly, this time from Thick (LVM) SR to Thin SR and the speed I got was around 16 MiB/s (which seems to be OK). I did write a post regarding this but deleted it since I need to dig deeper into this before I report this as an issue to you.
I will be conducting tests for a few more days just to be sure. (I am talking about Continuous Backup btw.)Update :
After a week of continuous testing, I am getting mixed results on the backup speed as mentioned in the above paragraph. I can now say that the issue may not be related to Linstor. -
Is there a procedure on how we can update our current 8.2 XCP-ng cluster to 8.3? My undertanding is that if I update the host using the ISO, it will effectively wipe all changes that were made to DOM0, including the linstor/sm-linstor packages.
-
@gb-123 are you using XOA or XO from sources?
If from sources the issue might come from having a different openssl when creating the sdn-controller certificates.
You can either try with an XOA or generate manually your certificates. -
@BenjiReis said in XOSTOR hyperconvergence preview:
@gb-123 are you using XOA or XO from sources?
If from sources the issue might come from having a different openssl when creating the sdn-controller certificates.
You can either try with an XOA or generate manually your certificates.Using XO from sources. I just turned on "Over-ride certificates" and reinstalled the whole XO virtual machine. Seems to work fine now.
My only problem was that why it suddenly stopped working when I installed Linstore as installing Linstor should not impact upon this. So thats why I reported this on this thread.
-
@gb-123 I see thanks
Just bad timing imho because Linstor doesn't touch this part of the host and the openssl issue is more probably coming from the env when you run your XO.
anyway, glad it's working now!
-