Issue after latest host update

RealTehreal

I'll do the testing on the weekend.

andyhhp

@RealTehreal Sorry to keep adding to the list of diagnostics, but everything here will help. After you've tried the other options, could you try this:

If the XTF testing shows any XTF test looping, use that single test, otherwise use your regular VM. Get one VM into the looping state. Check xl list to confirm that you've only got Domain-0 and the one other VM, and note it's domid (the "ID" column).

In dom0, run xentrace to capture a system trace. It's looping so the dump file is going to be large, but it also means that you can CTRL-C as quickly as you can on the shell and it will be fine (a few hundred milliseconds of samples will almost certainly be enough).

Anyway, run xentrace -D -e 0x0008f000 xentrace.dmp and then give me created xentrace.dmp file. If you're interested in what's in it, you can decode it using xenalyze -a xentrace.dmp |& less.

Then, run xen-hvmctx $domid two or three times, and share the output of all.

RealTehreal

@andyhhp said in Issue after latest host update:

@RealTehreal It's an Intel issue, but while this is enough to show that there is an issue, it's not enough to figure out what is wrong.

Sadly, a VM falling into a busy loop can be one of many things. It's clearly on the (v)BSP prior to starting (v)APs, hence why it's only ever a single CPU spinning.

Can you switch to using the debug hypervisor (change the /boot/xen.gz symlink to point at the -d suffixed hypervisor), and then capture xl dmesg after trying to boot one VM. Depending on how broken things are, we might see some diagnostics.

Could you also try running xtf as described here: https://xcp-ng.org/forum/post/57804 It's a long-shot, but if it does happen to stumble on the issue, then it will be orders of magnitude easier to debug than something misc broken in the middle of OVMF.

First things first: here some information.

xl dmesg with debug kernel, bad microcode and after trying to run a VM: xl_dmesg_bad_microcode.txt

xtf short: xtf_short.txt

xtf long: xtf_long.txt

RealTehreal

@andyhhp said in Issue after latest host update:

@RealTehreal Sorry to keep adding to the list of diagnostics, but everything here will help. After you've tried the other options, could you try this:

If the XTF testing shows any XTF test looping, use that single test, otherwise use your regular VM. Get one VM into the looping state. Check xl list to confirm that you've only got Domain-0 and the one other VM, and note it's domid (the "ID" column).

In dom0, run xentrace to capture a system trace. It's looping so the dump file is going to be large, but it also means that you can CTRL-C as quickly as you can on the shell and it will be fine (a few hundred milliseconds of samples will almost certainly be enough).

Anyway, run xentrace -D -e 0x0008f000 xentrace.dmp and then give me created xentrace.dmp file. If you're interested in what's in it, you can decode it using xenalyze -a xentrace.dmp |& less.

Then, run xen-hvmctx $domid two or three times, and share the output of all.

I sent you a pm.

andyhhp

@RealTehreal Thank-you very much for that information. I'll follow up with Intel.

In the short term, I'd recommend just using the old microcode.

olivierlambert

FYI I ordered and received a Mini PC based on a Celeron N4000 for internal testing (Gemini Lake "non-refresh"), and we were able to reproduce the issue

So as @andyhhp said, now we are 100% sure it's the microcode, it's up to Intel, who is now aware of this!

mr_zz

This post is deleted!

mr_zz

@nikade said in Issue after latest host update:

@RealTehreal said in Issue after latest host update:
@RealTehreal
Step-by-step instructions, in case, someone else has the same issue:

1.: yum history list to get the transaction id of the last update.

2.: yum history info # with # being the id from step 1, to list the updates done in this transaction. The interesting part for me was
Updated microcode_ctl-2:2.1-26.xs26.2.xcpng8.2.x86_64  
Update                2:2.1-26.xs28.1.xcpng8.2.x86_64
3.:yum downgrade microcode_ctl-2:2.1-26.xs26.2.xcpng8.2.x86_64 to downgrade to the previous version. You will have to enter the older version for this command.

4.: Wait until it's done, reboot, test, pray it'll work again.

This is just a workaround! Microcode updates are important security and/or functional updates. Downgrading can lead to security issues.
Thanks for sharing the resolution, im sure it will help someone else in the future.

@nikade Here I am!
Same problem (obviously) for Intel J4005 (I'm new to xcp-ng and I'm thinking about a homelab migration from Proxmox to an old NUC 7 as a test).
So thank you all very much for clarifying me which of the 65 updates (from the initial downloaded image) was the problem that was driving me crazy in these days of testing!

nikade

@mr_zz welcome to the forum

andyhhp

@RealTehreal I've got a fix from Intel, and @stormi has packaged it.

yum update microcode_ctl --enablerepo=xcp-ng-testing should get you microcode_ctl-2.1-26.xs29.2.xcpng8.2 which has the fixed microcode for this issue in it.

mgigirey

@andyhhp Any plans to update the intel-microcode for XCP-ng 8.3? latest know version working in my setup is intel-microcode-20231009-1.xcpng8.3.noarch.rpm

andyhhp

@mgigirey said in Issue after latest host update:

@andyhhp Any plans to update the intel-microcode for XCP-ng 8.3? latest know version working in my setup is intel-microcode-20231009-1.xcpng8.3.noarch.rpm

I am not an XCP-ng developer. You'll have to ask @stormi for that.

stormi

@mgigirey Yes, soon.

mgigirey

@stormi Thanks, looking forward.