XCP-ng host - Power management
-
Hi,
are there any configurable options for a basic power management policy similar to ESXi?
-
Question for @tjkreidl
-
@abudef Hello! It depends on many factors. Do you have any GPUs? What is the server model and its CPU configuration and specifics? What kind of VMs are you running?
Note that many CPU power settings can and should be performed in the BIOS. See for example this article, and let us know what your server configuration looks like. This article may be of some use to you:
https://community.citrix.com/citrix-community-articles/a-tale-of-two-servers-how-bios-settings-can-affect-your-apps-and-gpu-performance/ -
@tjkreidl Hello, I have two identical Dell R630 servers (BIOS 2.19.0) each with a pair of Intel E5-2680 v4 CPUs in my lab where I am testing deployment scenarios. In the lab, performance is not important, but instead I want to minimize power consumption. Ideally to be able to switch performance "profiles" without having to reboot the servers and toggling settings in the BIOS. Thanks for the link to the article, useful tips and advice there!
-
@abudef Thanks for your feedback. those should help since those servers appear to be of a similar vintage. Looks like you have 2 CPUs per server, so the memory will be physically split between the interconnects and hence NUMA will play a role. Let me know if you have specific questions after you go through all that information.
As an aside, the activity of the VMs will have a big influence on power consumption, probably more than various BIOS settings. Note that if you want to make
use of turbo mode and C states, you'll need to set the BIOS to OS control. Here's a pretty good thread that discusses Dell BIOS power state settings that
may be useful: https://serverfault.com/questions/74754/dell-poweredge-powersaving-bios-settings-differences
Power settings will only have a minimal effect on power consumption when the server is idle. I ran server that had something like 80 virtual desktop VMs on them set to high performance because during the day, they needed all the power they could get. When the labs closed at night, the power consumption went way down. But it's always best to verify what works or not in your very own environment, as I state many times in my articles!
Best regards,
Tobias -
Enabling various custates and frequency scaling in BIOS/Firmware can help powr consumption. There is some latency cost as it takes longer time from deeper states.
Linux also has CPU frequency governors, but I am not sure how the Xen kernel handles this. Remember that dom0 is a VM under Xen, so things aren't as simple as with plain bare-metal Linuxes.
There's some information here about this:
https://wiki.xenproject.org/wiki/Xen_power_management -
@Forza As mentioned, for VMs and the OS to be able to leverage such features as turbo mode and C-states, the BIOS has to be set to enable OS control. Without giving such control to the Linux OS, there are indeed various limitations. The uncore parameter must also be set to "dynamic" (OS DBPM) and if not in the BIOS, has to be set via the command:
xenpm set-scaling-governor performance
to put into effect immediately and to be able to be preserved over reboots, the command:
/opt/xensource/libexec/xen-cmdline --set-xen cpufreq=xen:performance
has to be run. This all assumes there have not been significant changes since I last tried all this out, of course, which was over four years ago, but @abudef has older hardware and I would think that would allow for this to be taken care of in the BIOS. To quote from my first article on this topic:
"Red Hat states specifically in the article https://access.redhat.com/articles/2207751 that a server should be set for OS (operating system) performance as otherwise, the operating system (in this case, XenServer) cannot gain access to control the CPU power management, which ties in with the ability to manage also the CPU frequency settings."BTW, the article you reference is now just about ten years old and references Xen kernel 3.4. The latest Xen release is 4.18.
