XCP-ng 8.1 Release Candidate now available!

r1

@Andrew said in XCP-ng 8.1 Release Candidate now available!:

Using xen-cmdline --set-xen dom0_mem changes the grub.cfg entries EXCEPT the default (first) kernel-alt entry. So yes, it works, but not for the alt kernel install. Not the end of the world, I can edit the file and move on. But, should it modify all xen config lines or just the default/first one?

xen-cmdline utility will only update the base kernel XCP-NG and XCP-ng (Serial), all other including kernel-alt are for debug purpose hence not touched. The script is also inherited from Citrix so its kept as-is.

Regarding the SMB ISO SR, it looks like XAPI or XAPI DB might have lost username/password in upgrade, this can be checked further in relevant code base.

Regarding XSConsole, if you have ssh access to the host, try to run it manually by # xsconsole and share the full error stack to trace further.

Andrew

The errors seem to be a boot time issue. When I run xsconsole from a shell I don't see the same errors.

stormi

If you have an XOA (any version) installed and can open a support tunnel, I'm willing to have a look at the issues as part of the RC phase.

Danp

Upgraded my R620 to the RC. Noticed the following during the boot process, but it eventually loaded and seems to be functioning fine thus far --

stormi

@peder said in XCP-ng 8.1 Release Candidate now available!:

@dariosplit I made a new 8.1-RC1 install and had the installer set up the Local SR as LVM.
After the installation I ran the commands in my previous example and afterwards 'mount' and 'file -sL' show that it's ext4.

HOWEVER; xsconsole still claims "Type : Ext3" so the console seems to have hard coded that "ext = ext3".
Something for RC2 sort out.

Now solved. Just run yum update, restart the xsconsole service, and it will display 'Ext' instead of 'Ext3'.

peder

@stormi Yes, that did it.
I suppose there's currently no way to show the actual filesystem, instead of the generic "Ext", in the xsconsole?
You have to resort to a shell and 'mount' or 'file -sL' to see that?

stormi

@peder That would require more than just a simple fix indeed.

stormi

I have pushed three new updates: kernel-alt, xcp-python-libs and xapi(-*).

kernel-alt updated to 4.19.108 by @r1
xcp-python-libs updated as a requirements for handling the grub configuration update when kernel-alt will be updated, now and in future updates
xapi updated with code by @BenjiReis to handle export and restore of VMs in a suspended state. This is a foundation for a future XO feature related to that.

Please update and make sure that you notice no regression related to those updates.

dariosplit

@stormi is the server restart necessary and how do I know with future updates if a server restart necessary

olivierlambert

Rule of thumb:

if there's an update on a kernel you are using in the dom0, you must reboot to run on the updated kernel
if there's a Xen update, idem
if there's a XAPI update, in most case, toolstack restart is enough
for other thing, it's more variable and hard to predict. But let's say in general, no mandatory reboot. However I'd like to stress that rebooting is a good thing, especially for all security related updates.

stormi

I'd add: if you don't reboot, always restart the toolstack. It's better to restart it for nothing than to forget to restart it. Note that the above Rule of thumb is also written in the updates howto.

For precise instructions related to any update, refer to the blog post that announces them (until we can get them directly in XO). I try to always give such instructions. Forgot here because it's the RC.

stormi

Final release is really close. I have built "pre-final" ISOs that do not differ much from the RC except from the updated kernel-alt, xcp-python-libs, xapi and xsconsole (replaced ext3 with ext in the local SR display since it can be either ext3 or ext4 depending on when the SR was created). Another fix: the netinstall ISO now correctly detects that it is a netinstall ISO when started in UEFI mode. The only visible change is that it doesn't offer local media anymore, consistently with the behaviour it already had in BIOS mode.

Things to test:

booting and installing kernel-alt
netinstall in UEFI
installation, basic features, coalesce...

ISOs can be downloaded from https://updates.xcp-ng.org/isos/8.1/

Biggen

@stormi

I've been holding out moving to 8 until it was finalized since I'm running the experimental ext4 driver. Can you confirm the following steps for transition to 8 if running the experimental ext4 driver?

Update to 8 and reboot
Copy/Export VMs somewhere off ext4 experimental SR
Unplug via CLI old experimental SR
Forget via CLI old experimental SR
Create new SR via CLI
Reinstall XO
Copy VMs back to new SR

Will the below command specifically create the new SR on the host/disk of my choosing using the new ext4 driver?

xe sr-create type=ext name-label=mySR host-uuid=<host_UUID> device-config:device=/dev/sdX

So the above command would create the new SR using ext4 just by giving it the type of ext?

I'm running MDRAID on this host and it appears that when running xe pbd-list it shows my SR in question is at device /dev/md127p4. That's partition 4 of the mdraid array that is holding the old experimental ext4 SR partition. I'm assuming when I run the above xe sr-create command that I want to make sure that I feed it device-config:device=/dev/md127p4.

It looks pretty straight forward if I have the above logic right. I'll have to find out how to find my host UUID but I'm sure that is pretty easy. Copying the VMs somewhere may be a larger and more time consuming challenge.

dariosplit

@stormi Will the RC release with yum update become the final release

stormi

@dariosplit Yes

stormi

@Biggen It's on my TODO list to write detailed instructions for that migration before the release. I'll follow the procedure myself and see what happens. Others can comment too and help making it perfect.

stormi

New updates are available for those who have installed the beta, the RC or from the pre-final ISOs. They fix an issue that no one had seen yet but very important: the chronyd service was not enabled when updating via yum, nor chrony-wait.service, vm.slice and sm-mpath-root.service (Citrix Hypervisor's update from 8.0 to 8.1 exhibits the same issue).

They also modify the tty console welcome message to mention Xen Orchestra as the official graphical client.

I have also built new ISOs ("prefinal2") with the updated packages. I hope those will be the final ones. Download from https://updates.xcp-ng.org/isos/8.1/

stormi

@stormi said in XCP-ng 8.1 Release Candidate now available!:

@Biggen It's on my TODO list to write detailed instructions for that migration before the release. I'll follow the procedure myself and see what happens. Others can comment too and help making it perfect.

Done: https://github.com/xcp-ng/xcp/wiki/XCP-ng-8.1-Release-Notes#migrate-from-experimental-ext4-storage-repositories

Biggen

@stormi

Can you export and import VMs with xcp-ng Center? I have a single host pool so I'm not sure what the best method is of exporting them and then importing them once the new SR is created.

My XO Community Edition resides on the experimental SR . So I can use that to move/export my other VMs first but I'm not sure how to move the actual XO CE last. I may have to simply reinstall it from scratch which isn't a big deal.

Danp

@Biggen Not sure if this will work for you, but I temporarily migrated my VDIs to my backup source (I created an NFS SR) and then deleted / recreated my local storage.