-
@ronan-a Wait a sec, maybe I found the root cause. I created a snapshot of a VM and deleted it. It created another base copy vdi and allocated space is now 200GB. MAybe I need to wait for the celanup job to take care of this?
-
@Swen The 150GiB are related to the base copy VDI yes.
Of course this value is just the maximum amount of data used because you use the thin LVM plugin. (It's not the real used data.)Regarding NIC, I didn't encounter any problems during my tests. The best way to measure the DRBD performance is to use
fio
directly in a VM and also on the host with a DRBD volume.The difference between local storage and DRBD is not a surprise:
- DRBD must sync the data between nodes
- DRBD is on top of LVM
-
@Swen
Writing zeros should result in nothing written with thin allocation (or dedup and compression): that's why I am hesitant to use /dev/zero as a source.Of course /dev/random could require to much of an overhead, depending on the quality and implementation which is why I like to use
fio
: a bit of initial effort to know and understand the tool, but much better control, especially when it comes to dealing with an OS that tries to be smart. -
@ronan-a did you use 10Gbit interfaces for linstor traffic? I am aware that there is a difference between local storage and DRBD, but if this difference is that high, linstor is not really interesting for high performance workloads. I need to be sure that the root cause it not related to my setup.
@ronan-a @abufrejoval which exact fio params are you using to test your environment and can you copy some numbers, so we can compare them?
-
We mostly use those displayed in this blog post: https://smcleod.net/tech/2016/04/29/benchmarking-io/
edit: depending on the storage, iodepth can be increased.
-
There is obviously tons of variations....
I've used this fio file a lot to quickly gain an understanding of how a bit of storage performs.
Basically it only uses a small 100MB file, but tells the OS to avoid buffering and then goes over that with a mix of reads and writes, mostly transitioning between block size, essentially going from super random to almost sequential in a single run.
It's helped me find issues with Gluster, identify network bandwidth issues or even find deteriorated RAIDs with a bad BBU. Creates the test file in the working directiory unless changed.
[global] filename=fio.file ioengine=libaio rw=randrw size=100m norandommap direct=1 iodepth=1 time_based runtime=10 [B512] bs=512 stonewall [B1k] bs=1k stonewall [B2k] bs=2k stonewall [b4k] bs=4k stonewall [b8k] bs=8k stonewall [b16k] bs=16k stonewall [b32k] bs=32k [b64k] bs=64k stonewall [b512k] bs=512k stonewall [b1m] bs=1m stonewall
Numbers: It should approach the network bandwidth towards the end (potentially divided by write amplification).
-
@ronan-a Hi,
I tested your branch and now the new added hosts to the pool are now attached to the XOSTOR. This is nice !
I have looked at the code, but I'm not sure if in the current state of your branch we can add a disk on the new host and update the replication ? I think not... but just to be sure.
-
@dumarjo
linstor resource-group modify --place-count=X
should be enough to update the replication. I'm not sure to add a command in the plugin now (but probably yes for XOA integration). -
@ronan-a said in XOSTOR hyperconvergence preview:
For some VMs that have built-in software replication/HA, like DBs, it might be prefered to have replication=1 set for the VDI.
We can authorize this behavior without having other SRs. It would suffice to pass a replication parameter for this particular VDI when it is created. So thank you for this feedback. I think we must implement this use case for the future.
@ronan-a Have anything been done regarding this feature? I scanned the thread, but I couldn't really find anything related to a new VDI option.
-
It might be done in the future, but that's not the priority for a v1
-
@olivierlambert
I just checked the sm repository, and it looks like it wouldn't be that complicated to add a new sm-config and pass it down to the volume creation. Do you accept PR/Contributions on that repository? We're really interested in this feature and I think I can take the time to write the code to handle this. -
The problem will be about to compute the available space if you have different replication number.
But in any cases, contributions are always welcome, we'll discuss details in PR.
-
I am trying this on pool with 5 hosts. Each host has a 4TB HDD installed that I am using for this.
Following the instructions here I download the installer and run it with
./install --disks /dev/sda --force
- this runs through and no errors are shown but right at the end it displays:Volume group "linstor_group" not found Cannot process volume group linstor_group Physical volume "/dev/sda" successfully created. Volume group "linstor_group" successfully created
But then checking the disk I don't see the expected partitions:
[09:12 XCPNG01 ~]# lsblk ... sda 8:0 0 3.7T 0 disk <nothing here> ...
Versions
[09:34 XCPNG01 ~]# uname -a Linux XCPNG01 4.19.0+1 #1 SMP Thu Jan 13 12:55:45 CET 2022 x86_64 x86_64 x86_64 GNU/Linux [09:28 XCPNG01 ~]# rpm -qa | grep -E "^(sm|xha)-.*linstor.*" sm-2.30.6-1.1.0.linstor.1.xcpng8.2.x86_64 xha-10.1.0-2.2.0.linstor.1.xcpng8.2.x86_64
I should mention that this disk was previously mounted as an SR but is no longer, and also was part of a glusterfs store but is no longer.
If I run
./install --disks /dev/sda --force
a second time it obviously has not much to do as it has installed everything but now I get a slightly different error:Package python-linstor-1.12.0-1.noarch already installed and latest version Nothing to do VG #PV #LV #SN Attr VSize VFree linstor_group 1 0 0 wz--n- <3.64t <3.64t Volume group "linstor_group" successfully removed Volume group "sda" not found Cannot process volume group sda Failed to execute vgremove properly.
What should I do to work out what the problem is?
-
Just reading through the
install
script, if thin provisioning is not used (i.e thick provisioning is) then the volume grouplinstor_group
will get created but no logical volume is created:if subprocess.call(['vgcreate', LINSTOR_GROUP] + disks): print('Failed to execute vgcreate properly.') return os.EX_SOFTWARE if thin and subprocess.call(['lvcreate', '-l', '100%FREE', '-T', '{}/thin_device'.format(LINSTOR_GROUP)]): print('Failed to create thin device properly.') return os.EX_SOFTWARE
So are the installation instructions incorrect? Step 3 where it states to check the config before proceeding it states to use
lsblk
to check that the LVM logical volumes are created - but it looks to me like this does not occur unless thin provisioning is used?I can see that the volume group has been created as you would expect by looking at the install script.
[08:41 XCPNG01 ~]# pvscan ... PV /dev/sda VG linstor_group lvm2 [<3.64 TiB / <3.64 TiB free] ... [08:35 XCPNG01 ~]# vgdisplay ... --- Volume group --- VG Name linstor_group System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 1 VG Access read/write VG Status resizable MAX LV 0 Cur LV 0 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size <3.64 TiB PE Size 4.00 MiB Total PE 953861 Alloc PE / Size 0 / 0 Free PE / Size 953861 / <3.64 TiB VG UUID uidJ13-juc7-2cm0-NnkV-wdhA-4fNm-HAWrgh
Am I misunderstanding the instructions somehow or missing something?
-
Pinging @ronan-a
-
@geoffbland Without thin option, no LVM volume is created. It's expected. You must just have a VG :
# vgs VG #PV #LV #SN Attr VSize VFree VG_XenStorage-11daa412-d2b5-cb7c-e8ae-847821e367a6 1 1 0 wz--n- 144.23g 144.23g linstor_group
A LVM volume is only required for the thin driver of LINSTOR.
I updated the main post, it was not totally clear.Regarding the force option, I fixed it here: https://gist.githubusercontent.com/Wescoeur/7bb568c0e09e796710b0ea966882fcac/raw/6aacde6b5c55f8e7b70ed585c59b9c2d54a2ea69/gistfile1.txt
It must be:
subprocess.call(['vgremove', '-f', LINSTOR_GROUP, '-y'])
instead of:
subprocess.call(['vgremove', '-f', LINSTOR_GROUP, '-y'] + disks)
-
@ronan-a said in XOSTOR hyperconvergence preview:
I updated the main post, it was not totally clear.
Thanks for that. I expected this was the case but wanted to be sure.
Looks like this is working so far then I will continue with my installation & testing. -
XOSTOR is now successfully installed on all 5 of my nodes in the cluster.
I ran this command (I'm assuming that this only needs running on one host?).
xe sr-create type=linstor name-label=XOSTOR01 host-uuid=28af0626-7788-4104-9449-xxxxxxxxxxxx device-config:hosts=XCPNG01,XCPNG02,XCPNG03,XCPNG04,XCPNG05 device-config:group-name=linstor_group device-config:redundancy=3 shared=true device-config:provisioning=thick
And this returned the SR UUID
cf896912-cd71-d2b2-488a-xxxxxxxxxxxx
this looks like it worked as expected.Running
linstor node list
shows the following:[12:01 XCPNG01 ~]# linstor node list โญโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโฎ โ Node โ NodeType โ Addresses โ State โ โโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโก โ XCPNG01 โ COMBINED โ 192.168.1.41:3366 (PLAIN) โ Online โ โ XCPNG02 โ COMBINED โ 192.168.1.42:3366 (PLAIN) โ Online โ โ XCPNG03 โ COMBINED โ 192.168.1.43:3366 (PLAIN) โ Online โ โ XCPNG04 โ COMBINED โ 192.168.1.44:3366 (PLAIN) โ Online โ โ XCPNG05 โ COMBINED โ 192.168.1.45:3366 (PLAIN) โ Online โ โฐโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโฏ [12:05 XCPNG01 ~]# linstor volume list โญโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโฎ โ Node โ Resource โ StoragePool โ VolNr โ MinorNr โ DeviceName โ Allocated โ InUse โ State โ โโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโก โ XCPNG01 โ xcp-persistent-database โ DfltDisklessStorPool โ 0 โ 1000 โ /dev/drbd1000 โ โ InUse โ Diskless โ โ XCPNG02 โ xcp-persistent-database โ DfltDisklessStorPool โ 0 โ 1000 โ /dev/drbd1000 โ โ Unused โ Diskless โ โ XCPNG03 โ xcp-persistent-database โ xcp-sr-linstor_group โ 0 โ 1000 โ /dev/drbd1000 โ 1.00 GiB โ Unused โ UpToDate โ โ XCPNG04 โ xcp-persistent-database โ xcp-sr-linstor_group โ 0 โ 1000 โ /dev/drbd1000 โ 1.00 GiB โ Unused โ UpToDate โ โ XCPNG05 โ xcp-persistent-database โ xcp-sr-linstor_group โ 0 โ 1000 โ /dev/drbd1000 โ 1.00 GiB โ Unused โ UpToDate โ โฐโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโฏ
Strangely running
linstor node list
only works on node XCPNO01, on the other 4 nodes I get the errorError: Unable to connect to linstor://localhost:3370: [Errno 99] Cannot assign requested address
. Is this expected?However when I check on XO (from sources) it shows one of the hosts is disconnected.
When I try to connect it from XO I get this error, is this related to the problem with linstor commands only working on one host XCPNG01?
pbd.connect { "id": "8040176c-16da-674d-e9bd-708c3a66e68a" } { "code": "SR_BACKEND_FAILURE_47", "params": [ "", "The SR is not available [opterr=Error: Unable to connect to any of the given controller hosts: ['linstor://XCPNG01']]", "" ], "task": { "uuid": "c92909b2-8a4e-e071-3c91-0c89a32b1e01", "name_label": "Async.PBD.plug", "name_description": "", "allowed_operations": [], "current_operations": {}, "created": "20220516T11:12:41Z", "finished": "20220516T11:13:11Z", "status": "failure", "resident_on": "OpaqueRef:a1e9a8f3-0a79-4824-b29f-d81b3246d190", "progress": 1, "type": "<none/>", "result": "", "error_info": [ "SR_BACKEND_FAILURE_47", "", "The SR is not available [opterr=Error: Unable to connect to any of the given controller hosts: ['linstor://XCPNG01']]", "" ], "other_config": {}, "subtask_of": "OpaqueRef:NULL", "subtasks": [], "backtrace": "(((process xapi)(filename lib/backtrace.ml)(line 210))((process xapi)(filename ocaml/xapi/storage_access.ml)(line 32))((process xapi)(filename ocaml/xapi/xapi_pbd.ml)(line 182))((process xapi)(filename ocaml/xapi/message_forwarding.ml)(line 128))((process xapi)(filename lib/xapi-stdext-pervasives/pervasiveext.ml)(line 24))((process xapi)(filename ocaml/xapi/rbac.ml)(line 231))((process xapi)(filename ocaml/xapi/server_helpers.ml)(line 103)))" }, "message": "SR_BACKEND_FAILURE_47(, The SR is not available [opterr=Error: Unable to connect to any of the given controller hosts: ['linstor://XCPNG01']], )", "name": "XapiError", "stack": "XapiError: SR_BACKEND_FAILURE_47(, The SR is not available [opterr=Error: Unable to connect to any of the given controller hosts: ['linstor://XCPNG01']], ) at Function.wrap (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/_XapiError.js:16:12) at _default (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/_getTaskResult.js:11:29) at Xapi._addRecordToCache (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/index.js:949:24) at forEach (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/index.js:983:14) at Array.forEach (<anonymous>) at Xapi._processEvents (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/index.js:973:12) at Xapi._watchEvents (/opt/xo/xo-builds/xen-orchestra-202204291839/packages/xen-api/src/index.js:1139:14)" }
XCPNG02 is the XCPNG pool master and also the host that I ran the
xe sr-create
command on to create the SR.What do I need to look at now to resolve this?
-
@geoffbland Well it's a known error resolved in this commit: https://github.com/xcp-ng/sm/commit/df92fcf7193f7f87fd03423293589fb50faa246d
You can modify
/opt/xensource/sm/linstorvolumemanager.py
with this fix on each node, it should repair the PBD connection.FYI, we planned to release a new beta with all our fixes before the end of this month.
-
@ronan-a Thanks that fixed it and all hosts now have the SR connected.
Running
linstor node list
only works on node XCPNO01, on the other 4 nodes I get the errorError: Unable to connect to linstor://localhost:3370: [Errno 99] Cannot assign requested address
still. Is this expected?