@olivierlambert @prilly Just loaded the XCP-ng 8.0 successfully on a Dell C6100 with 2 x L5630.

No errors during install, and boots up just fine for use.

@Prilly I installed Citrix Hypervisor 8.0 on my Dell C6100 which is running L5630 CPU and it booted just fine.

Not sure the issue, but rebooted the host and everything is fine again. I definitely had rebooted the host twice though after applying the patches and physically unplugged and moved the host.

XCP-NG 8.3 - two hosts in my pool, both have the latest patches and rebooted (I moved the physical location of the servers).

I am trying to migrate VMs from one to another and they get to around 85-95% complete and then just time out.

Tried to shutdown the VMs to attempt a migration when not live, and the "console" disappears from XO for the VM.

xe vm-list shows the VM in a running state.

Tried to do: xe vm-shutdown uuid=XXX and it just sits there with no error

Restarted the Toolstack on both hosts multiple times. I want to avoid restarting the host as I have a lot of VMs running on it and also worried then non of these VMs will start back up.

[19:08 cloud ~]# rpm -qa |grep xen
xengt-userspace-4.0.0-1.xcpng8.3.noarch
xenserver-hwdata-20240411-1.xcpng8.3.noarch
xen-dom0-libs-4.17.6-5.2.xcpng8.3.x86_64
xen-libs-4.17.6-5.2.xcpng8.3.x86_64
xenopsd-xc-26.1.3-1.3.xcpng8.3.x86_64
xenopsd-cli-26.1.3-1.3.xcpng8.3.x86_64
xen-hypervisor-4.17.6-5.2.xcpng8.3.x86_64
xen-dom0-tools-4.17.6-5.2.xcpng8.3.x86_64
xenopsd-26.1.3-1.3.xcpng8.3.x86_64
xenserver-dracut-10-2.xcpng8.3.noarch
xen-crashdump-analyser-2.6.1-1.xcpng8.3.x86_64
xenserver-status-report-2.0.15-1.xcpng8.3.noarch
mellanox-mlnxen-5.9_0.5.5.0-3.1.xcpng8.3.x86_64
xen-tools-4.17.6-5.2.xcpng8.3.x86_64

Reboot seems to have fixed it and made it visible. Leaving this post up so others have all the commands in one place.

[14:15 cloud ~]# ethtool -i eth5
driver: i40e
version: 2.26.8
firmware-version: 9.50 0x8000f255 23.0.8
expansion-rom-version:
bus-info: 0000:5e:00.1
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes

I am trying to get an Intel X710-DA2 working with a fresh load of 8.3.

This is on a Dell R640 server - the bios and idrac see the X710 in slot 2.

lspci and modprobe see the card - but ifconfig and ethtools does not.

I loaded the alt drivers: yum install intel-i40e-alt --enablerepo=xcp-ng-testing

rmmod i40e
modprobe i40e

lspci sees the card.

[12:58 cloud extra]# lspci |grep 710
5e:00.0 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)
5e:00.1 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)

modinfo i40e

[13:00 cloud extra]# modinfo i40e
filename:       /lib/modules/4.19.0+1/override/i40e.ko
version:        2.26.8
license:        GPL
description:    Intel(R) 40-10 Gigabit Ethernet Connection Network Driver
author:         Intel Corporation, <e1000-devel@lists.sourceforge.net>
srcversion:     666622D0DB1EB24725D7453
alias:          pci:v00008086d0000158Bsv*sd*bc*sc*i*
alias:          pci:v00008086d0000158Asv*sd*bc*sc*i*
alias:          pci:v00008086d00000DDAsv*sd*bc*sc*i*
alias:          pci:v00008086d000037D3sv*sd*bc*sc*i*
alias:          pci:v00008086d000037D2sv*sd*bc*sc*i*
alias:          pci:v00008086d000037D1sv*sd*bc*sc*i*
alias:          pci:v00008086d000037D0sv*sd*bc*sc*i*
alias:          pci:v00008086d000037CFsv*sd*bc*sc*i*
alias:          pci:v00008086d000037CEsv*sd*bc*sc*i*
alias:          pci:v00008086d00000D58sv*sd*bc*sc*i*
alias:          pci:v00008086d00000CF8sv*sd*bc*sc*i*
alias:          pci:v00008086d00001588sv*sd*bc*sc*i*
alias:          pci:v00008086d00001587sv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Fsv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Esv*sd*bc*sc*i*
alias:          pci:v00008086d000015FFsv*sd*bc*sc*i*
alias:          pci:v00008086d00001589sv*sd*bc*sc*i*
alias:          pci:v00008086d00001586sv*sd*bc*sc*i*
alias:          pci:v00008086d0000101Fsv*sd*bc*sc*i*
alias:          pci:v00008086d00000DD2sv*sd*bc*sc*i*
alias:          pci:v00008086d00001585sv*sd*bc*sc*i*
alias:          pci:v00008086d00001584sv*sd*bc*sc*i*
alias:          pci:v00008086d00001583sv*sd*bc*sc*i*
alias:          pci:v00008086d00001581sv*sd*bc*sc*i*
alias:          pci:v00008086d00001580sv*sd*bc*sc*i*
alias:          pci:v00008086d00001574sv*sd*bc*sc*i*
alias:          pci:v00008086d00001572sv*sd*bc*sc*i*
depends:
retpoline:      Y
name:           i40e
vermagic:       4.19.0+1 SMP mod_unload modversions
parm:           debug:Debug level (0=none,...,16=all) (int)
parm:           l4mode:L4 cloud filter mode: 0=UDP,1=TCP,2=Both,-1=Disabled(default) (int)
parm:           enable_fw_lldp:Don't disable FW-LLDP during NIC init (bool)

Not sure why I can't find an ethX for the card under ifconfig or ethtools.

@olivierlambert @prilly Just loaded the XCP-ng 8.0 successfully on a Dell C6100 with 2 x L5630.

No errors during install, and boots up just fine for use.

@Prilly I installed Citrix Hypervisor 8.0 on my Dell C6100 which is running L5630 CPU and it booted just fine.