@planedrop Not opposed to cloud of course, but it's a network with no internet!

@Pilow Time for a drink, I think.

Well, scratch the help, I have fixed it.

Bad VM:

xe vm-param-list uuid={uuid} | grep "other-config"

other-config (MRW): xo:backup:schedule: one-time; xo:backup:vm: {uuid}; xo:backup:datetime: 20260214T18:13:03Z; xo:backup:job: 97665b6d-1aff-43ba-8afb-11c7455c16ff; xo:backup:sr: {uuid}; auto_poweron: true; base_template_name: Debian Buster 10;

Clean VM:

other-config (MRW): auto_poweron: true; base_template_name: Debian Buster 10; [...]

Stale references to my old backup job causing the VM to disassociate with the VDI chain. Removing the extra config resolved it. Simple when you know where to look.

xe vm-param-remove uuid={uuid} param-name=other-config param-key=xo:backup:job
xe vm-param-remove uuid={uuid}  param-name=other-config param-key=xo:backup:sr
xe vm-param-remove uuid={uuid}  param-name=other-config param-key=xo:backup:vm
xe vm-param-remove uuid={uuid}  param-name=other-config param-key=xo:backup:schedule
xe vm-param-remove uuid={uuid}  param-name=other-config param-key=xo:backup:datetime

VMs now snapshot clean.

Edit: For anyone with this issue, stopping and starting the Openmetrics plugin after saving the password in XO fixed it.

I keep getting the {"error":"Query authentication does not match server setting"} problem, is there something I'm missing? I run XO proxied through Nginx with HTTPS, is there some additional config required to get it working? I have set the key with openssl rand -hex 32 and have verified that is saved correctly in the plugin, and that I am using the same key for curl. I am able to obtain the /health endpoint as expected, I just cannot obtain the full metrics, only returns that error.

Command:

curl --insecure -H "Authorization: Bearer mytoken" https://xo.mydomain.local/openmetrics/metrics

XO commit:

91c5d

I should note that running the command inside my Docker container returns only the error, including the health endpoint. Do I need to expose 9004?

@julien-f Thank you and thank you for the quick resolution, you guys rock.

@olivierlambert Yes but didn't see any changes for backup/logs which is where the issue seemed to arise from. I pull the status from each log entry not the job info itself.

@julien-f awesome, thanks!

Testing the agent out on Arch Linux (mainly due to the spotty 'support' in the AUR/generally) and it is working fine - better than what I had before (which did not report VM info properly). I've set it up as a systemd service to replace the previous one I had, also working as expected.

This would be fun to contribute towards.

For anyone who comes across this, you can just add an exception for your management page and shift will work on the console.

Settings > Privacy & Security > Enhanced Tracking Protection > Manage Exceptions > Add the site url e.g. https://xo.fqdn.com.

@timemaster5 Ah very cool, thank you for looking into this and the comprehensive write up, great work. I went on a small journey to try various workarounds but didn't get as far as yourself and others, particularly as my use-case is only a "nice-to-have". Most everything I found was in relation to Proxmox and others. Little did I know when I thought I was helping you over on Github, you would actually end up helping me!

As I understand from your notes, the full procedure would be:

1. Enable passthrough for the GPU on the host
2. Apply the patched wrapper to enable custom model args and respect platform vga
3. Disable emulated VGA via platform:vga=none
4. Apply the config to the VM via -device loader options
5. Reboot the host
6. Mount the GPU to the VM and boot it up

@TeddyAstie Thanks for the update.

I do actually have a VBIOS for that GPU, but I wasn't entirely sure what to do with it - is there a process to inject it? I've found resources for Proxmox and others, but I really like XCP and equally I don't want to migrate my entire setup just for that.

If it's really tricky then I'm not too worried about it, as I say the VM actually runs the cameras perfectly fine on CPU alone, it's negligible.

Edit: Looks like this post might answer my question: https://github.com/xcp-ng/xcp/issues/786

"Even when specifying romfile and rombar properties on the xen-pci-passthrough device in QEMU, the ROM region is not mapped into guest memory."

timemaster5 created this issue in xcp-ng/xcp

open PCI ROM BAR not exposed to guest when using xen-pci-passthrough #786

@TeddyAstie yarp.

My bad, the VM has it as 00:08.0 but on the host it's actually 00:06.0, I just didn't think about the specifics of your request!

06:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Barcelo (rev c1) (prog-if 00 [VGA controller])
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 1636
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 38
	Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=2M]
	Region 4: I/O ports at d000 [size=256]
	Region 5: Memory at fca00000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: [48] Vendor Specific Information: Len=08 <?>
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [64] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 256 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 8GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
		LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+, EqualizationPhase1+
			 EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
	Capabilities: [a0] MSI: Enable- Count=1/4 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [c0] MSI-X: Enable- Count=4 Masked-
		Vector table: BAR=5 offset=00042000
		PBA: BAR=5 offset=00043000
	Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [270 v1] #19
	Capabilities: [2a0 v1] Access Control Services
		ACSCap:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
		ACSCtl:	SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
	Capabilities: [2b0 v1] Address Translation Service (ATS)
		ATSCap:	Invalidate Queue Depth: 00
		ATSCtl:	Enable-, Smallest Translation Unit: 00
	Capabilities: [2c0 v1] Page Request Interface (PRI)
		PRICtl: Enable- Reset-
		PRISta: RF- UPRGI- Stopped+
		Page Request Capacity: 00000100, Page Request Allocation: 00000000
	Capabilities: [2d0 v1] Process Address Space ID (PASID)
		PASIDCap: Exec+ Priv+, Max PASID Width: 10
		PASIDCtl: Enable- Exec- Priv-
	Capabilities: [400 v1] #25
	Capabilities: [410 v1] #26
	Capabilities: [440 v1] #27
	Kernel driver in use: pciback

@Greg_E Thanks, I've got another thread up and it's potentially being addressed!

@TeddyAstie Sure no problem.

lspci -vvv -s 00:08.0

00:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Renoir PCIe Dummy Host Bridge
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Host is Debian, slightly older kernel so that may be why? Happy to try a different VM distro if you think it might help.

Linux cctv 6.12.69+deb13-amd64 #1 SMP PREEMPT_DYNAMIC Debian 6.12.69-1 (2026-02-08) x86_64 GNU/Linux

@itnok fair enough and understandable, thanks for taking the time to reply.

@TeddyAstie Thanks for that - I was going off of other old XCP hosts I have had running that did show IOMMU info there, so I figured it wasn't working on these particular machines. I also had the the Intel GPU working on those hosts, which further supported my theory. I do have a USB controller passed through to the same VM and that works perfectly, basically native functionality, but from the research I was doing it was suggested USB controllers are way less bothered about imperfect passthrough.

I was able to find a ROM for my particular GPU, but I don't know what - if anything - I can do with it in XCP. I've found lots of info for QEMU and Proxmox, but I'm not sure they directly translate.

If there's nothing I can do for the moment then I can live without the GPU, running decode on the CPU isn't really taxing it that much. Appreciate you looking into it.

@itnok hey, did you ever get this working? I am in a similar position now with the ROM header.

I am trying to pass through my AMD GPU to a Debian host. This sort of succeeds, but I am getting error messages about a "BIOS ROM". I have had a look online and found some resources to suggest how to provide one, but I am quite unsure on that and cannot locate a specific one for my GPU (AMD Ryzen 7 5825U with Radeon Graphics, I think Vega 8).

I am showing it has at least tried to load/associate the kernel module:

lspci -nnk -s 00:08.0
00:08.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Barcelo [1002:15e7] (rev c1)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device [1002:1636]
	Kernel modules: amdgpu

But dmesg output states it cannot locate a ROM.

[    4.655776] amdgpu 0000:00:08.0: amdgpu: Unable to locate a BIOS ROM
[    4.655797] amdgpu 0000:00:08.0: amdgpu: Fatal error during GPU init
[    4.655812] amdgpu 0000:00:08.0: amdgpu: amdgpu: finishing device.
[    4.656681] amdgpu 0000:00:08.0: probe with driver amdgpu failed with error -22

Is there a trick to this, has anyone had success with this kind of AMD GPU? On my old hosts, enabling pass through was enough for it to just kind of work (Intel HD 530). The host machine outputs to a display normally when the card is in-use by the host. I am of the understanding the ROM is just part of the motherboard/GPU, there is some suggestion it can be dumped from the host-side, but I'm unsure on this.

Can anyone shed some light on how this should work, or whether it's just something in my setup that isn't working? I have IOMMU and SR-IOV enabled in the BIOS, but I don't know if it's working.

EDIT: It looks like I may just have a fake BIOS? The settings to enable all the relevant components (IOMMU, DMAr support etc) don't actually seem to do anything, they might just be for show - dmesg | grep -i iommu returns nothing, dmesg | grep -i -e dmar -e vfio -e pciback only shows pciback info, and cat /proc/cmdline contains nothing about IOMMU. Oddly, XO is still reporting that IOMMU is enabled:

The output of xe host-param-get uuid={uuid} param-name=chipset-info also returns iommu: true, but the output of xl info | grep "iommu" returns nothing.

@florent No problem, just thought it would be fun.

Thanks for your work anyway!