Add Management Interface

olivierlambert

Please share the screenshots so we can see how, that might be helpful to us

KPS

olivierlambert
Sure!

olivierlambert

So this replace the previous mgmt interface?

KPS

olivierlambert
Yes and no...
There are two points:

Moving primary management to bond (--> Management)
Adding two additional management interfaces for iSCSI (-> iSCSI1811 and iSCSI1812)

Both was/is critical for me to setup an HA-environment with MPIO-iSCSI and I did not yet find and possibility to add a second/third management interface with XOA

Andrew

KPS The two tools are a little different. You actually only have ONE management interface for XCP. The other 'management' interfaces shown are just extra ones that have IP addresses assigned in XCP verses an interface without an IP used for VMs.

In XO you can just assign a static IP to the other ethernet interfaces (or VLAN interfaces) and then use them for iSCSI/NFS. As long as your new interface on the XCP host and iSCSI target are on the same IP network then that's what will be used.

olivierlambert

I have to admit that's a bit confusing to me (but I'm busy doing other stuff in parallel). If there's something missing in XO with a precise spec/steps, I'll be happy to consider to add it

KPS

olivierlambert
What is confising?

Having Management on a bond --> is best-practice for HA
Having an additional Management Interface --> is mandatory for MPIO which is best-practice for HA

Currently, I have no idea on how I could set this up in a "world without XCP-ng-center"
At least, I was not able to do this with XOA

dredknight

olivierlambert the additional IP is used when one have a dedicated network for ISCSI network traffic. Here are some examples;

Case 1
imagine you have host 3 interfaces:

eth0 is xcp management - 10.10.10.10
eth1 is trunk for vlans - <trunk>
eth2 is free and you want to use its bandwidth to attach your new ISCSI Storage. This way you can get the maximum bandwidth possible as eth2 is not overlapping with eth0. ISCSI configuration requires assigned IP on the interface but does not require it to be of type management (as eth0).

Case 2
Same as the previous one except the user decides to setup the ISCSI network ip on management interface.

olivierlambert

But you can already add an IP to an interface in Xen Orchestra I'm sure I'm missing something obvious

dredknight

olivierlambert I was just trying to describe it better. If that is the case then all is good.

KPS

olivierlambert said in Add Management Interface:

But you can already add an IP to an interface in Xen Orchestra I'm sure I'm missing something obvious

That is exactly my problem: I do not find a possibility to add an ip address to an interface. I can only change the IP of a management interface, that is already there...

olivierlambert

In the host view, Network tab, in each row you have eth0, eth1 etc.
Click on the "None" in the row "Mode".
Profit.

KPS

olivierlambert
Thank you very much! I just did not bring that option to my demand...

Sorry for the confusion!

olivierlambert

No worries, the UI isn't clear at all and we are aware of it.

So what's left that you don't have in XCP-ng Center after this?

KPS

Hi!

I was now able to solve both issues (thank you olivierlambert):

Adding additional Management Interface:
--> XOA - Host - Network - Change Type to "static"
Moving Management Interface to Bond:
--> XOA - Pool - Network - Create Bond with "old" single-Interface and another interface
----> IP is automatically reassigned to Bond

Gheppy

One more question.
How to change Management, let's say, on eth3. In the image below.

Andrew

Gheppy olivierlambert You can do it from XCP directly. Look at this post #4671. There is a menu option on the XCP console or using xsconsole from the XCP shell. You should reboot after changing the management interface.

Gheppy

Andrew
I know about xsconsole, I thought there was something like that in XO as well as in the mentioned post where XCP-ng Center is used for this.

Andrew

Gheppy I think the change of management interface and change MTU are missing features that are available from the CLI or the old XCP-ng Center and should be supported in XO (right olivierlambert ? SVP).

olivierlambert

Yes it will