-
@splastunov The DotHill certainly wasn't great for scaling out, because of the age of the firmware and the old-school treatment of the disk arrays.
We did deploy several disk expansion trays that were part populated at purchase as some level of expansion, and operated most of the array as a single underlying pool, which was then split up into iSCSI presented volumes.
So the limitations of the DotHill controllers and firmware we were using didn't address the storage pool scaling issue that CEPH / GPFS / etal are designed to.
However, some of the newer filer heads that treat their entire available disk array as a consolidated pool and support iSCSI would have that scalability, whilst keeping the hypervisor side relatively straight-forward.
CEPH etal are also in a much more mature place than they were back in the early 2010s too, so if I was doing it again, maybe we would go for a solution architecture based around that. Or XOSTOR, of course!
My intent was to present an iSCSI setup instance as something we found relatively bomb-proof, and post-initial configuration, relatively easy to scale. We provisioned 24 port A and B side network switches with jumbo frame support to give us the scalability to add further pools of hypervisors or storage, as required.
-
The typical hypervisor node was provisioned with at least 4 network ports, but most had 8 to allow trunking/resilience for every connection:
Management + live migration (Isolated)
World (Trunk)
iSCSI-A
iSCSI-BThe DotHills were 4 ports per controller, and the two controllers were configured as:
Management
iSCSI-A
iSCSI-B
SpareThe iSCSI-A and iSCSI-B were simple web-managed procurves with 24 ports each.
We had this scaled to 12 hypervisor nodes in 3 pools, all running off the same underlying dothill (dual redundant controller) hardware. We had provisioned some local SSD storage in each hypervisor for any nodes that were struggling for IOPs but ultimately never needed that.
-
OK we have debugged and improved this process, so including it here if it helps anyone else.
How to migrate resources between XOSTOR (linstor) clusters. This also works with piraeus-operator, which we use for k8s.
Manually moving listor resource with thin_send_recv
Migration of data
Commands
# PV: pvc-6408a214-6def-44c4-8d9a-bebb67be5510 # S: pgdata-snapshot # s: 10741612544B #get size lvs --noheadings --units B -o lv_size linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 #prep lvcreate -V 10741612544B --thinpool linstor_group/thin_device -n pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 linstor_group #create snapshot linstor --controller original-xostor-server s create pvc-6408a214-6def-44c4-8d9a-bebb67be5510 pgdata-snapshot #send thin_send linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000_pgdata-snapshot 2>/dev/null | ssh root@new-xostor-server-01 thin_recv linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 2>/dev/nullWalk-through
Prep migration
[13:29 original-xostor-server ~]# lvs --noheadings --units B -o lv_size linstor_group/pvc-12aca72c-d94a-4c09-8102-0a6646906f8d_00000 26851934208B [13:53 new-xostor-server-01 ~]# lvcreate -V 26851934208B --thinpool linstor_group/thin_device -n pvc-12aca72c-d94a-4c09-8102-0a6646906f8d_00000 linstor_group Logical volume "pvc-12aca72c-d94a-4c09-8102-0a6646906f8d_00000" created.Create snapshot
15:35:03] jonathon@jonathon-framework:~$ linstor --controller original-xostor-server s create pvc-12aca72c-d94a-4c09-8102-0a6646906f8d s_test SUCCESS: Description: New snapshot 's_test' of resource 'pvc-12aca72c-d94a-4c09-8102-0a6646906f8d' registered. Details: Snapshot 's_test' of resource 'pvc-12aca72c-d94a-4c09-8102-0a6646906f8d' UUID is: 3a07d2fd-6dc3-4994-b13f-8c3a2bb206b8 SUCCESS: Suspended IO of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'ovbh-vprod-k8s04-worker02' for snapshot SUCCESS: Suspended IO of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'original-xostor-server' for snapshot SUCCESS: Took snapshot of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'ovbh-vprod-k8s04-worker02' SUCCESS: Took snapshot of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'original-xostor-server' SUCCESS: Resumed IO of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'ovbh-vprod-k8s04-worker02' after snapshot SUCCESS: Resumed IO of '[pvc-12aca72c-d94a-4c09-8102-0a6646906f8d]' on 'original-xostor-server' after snapshotMigration
[13:53 original-xostor-server ~]# thin_send /dev/linstor_group/pvc-12aca72c-d94a-4c09-8102-0a6646906f8d_00000_s_test 2>/dev/null | ssh root@new-xostor-server-01 thin_recv linstor_group/pvc-12aca72c-d94a-4c09-8102-0a6646906f8d_00000 2>/dev/nullNeed to yeet errors on both ends of command or it will fail.
This is the same setup process for replica-1 or replica-3. For replica-3 can target new-xostor-server-01 each time, for replica-1 be sure to spread them out right.
Replica-3 Setup
Explanation
thin_sendto new-xostor-server-01, will need to run commands to force sync of data to replicas.Commands
# PV: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 # snapshot: snipeit-snapshot # size: 21483225088B #get size lvs --noheadings --units B -o lv_size linstor_group/pvc-96cbebbe-f827-4a47-ae95-38b078e0d584_00000 #prep lvcreate -V 21483225088B --thinpool linstor_group/thin_device -n pvc-96cbebbe-f827-4a47-ae95-38b078e0d584_00000 linstor_group #create snapshot linstor --controller original-xostor-server s create pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 snipeit-snapshot linstor --controller original-xostor-server s l | grep -e 'snipeit-snapshot' #send thin_send linstor_group/pvc-96cbebbe-f827-4a47-ae95-38b078e0d584_00000_snipeit-snapshot 2>/dev/null | ssh root@new-xostor-server-01 thin_recv linstor_group/pvc-96cbebbe-f827-4a47-ae95-38b078e0d584_00000 2>/dev/null #linstor setup linstor --controller new-xostor-server-01 resource-definition create pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 --resource-group sc-74e1434b-b435-587e-9dea-fa067deec898 linstor --controller new-xostor-server-01 volume-definition create pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 21483225088B --storage-pool xcp-sr-linstor_group_thin_device linstor --controller new-xostor-server-01 resource create --storage-pool xcp-sr-linstor_group_thin_device --providers LVM_THIN new-xostor-server-01 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 linstor --controller new-xostor-server-01 resource create --auto-place +1 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 #Run the following on the node with the data. This is the prefered command drbdadm invalidate-remote pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 #Run the following on the node without the data. This is just for reference drbdadm invalidate pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 linstor --controller new-xostor-server-01 r l | grep -e 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584'--- apiVersion: v1 kind: PersistentVolume metadata: name: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 annotations: pv.kubernetes.io/provisioned-by: linstor.csi.linbit.com finalizers: - external-provisioner.volume.kubernetes.io/finalizer - kubernetes.io/pv-protection - external-attacher/linstor-csi-linbit-com spec: accessModes: - ReadWriteOnce capacity: storage: 20Gi # Ensure this matches the actual size of the LINSTOR volume persistentVolumeReclaimPolicy: Retain storageClassName: linstor-replica-three # Adjust to the storage class you want to use volumeMode: Filesystem csi: driver: linstor.csi.linbit.com fsType: ext4 volumeHandle: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 volumeAttributes: linstor.csi.linbit.com/mount-options: '' linstor.csi.linbit.com/post-mount-xfs-opts: '' linstor.csi.linbit.com/uses-volume-context: 'true' linstor.csi.linbit.com/remote-access-policy: 'true' --- apiVersion: v1 kind: PersistentVolumeClaim metadata: annotations: pv.kubernetes.io/bind-completed: 'yes' pv.kubernetes.io/bound-by-controller: 'yes' volume.beta.kubernetes.io/storage-provisioner: linstor.csi.linbit.com volume.kubernetes.io/storage-provisioner: linstor.csi.linbit.com finalizers: - kubernetes.io/pvc-protection name: pp-snipeit-pvc namespace: snipe-it spec: accessModes: - ReadWriteOnce resources: requests: storage: 20Gi storageClassName: linstor-replica-three volumeMode: Filesystem volumeName: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584Walk-through
jonathon@jonathon-framework:~$ linstor --controller new-xostor-server-01 resource-definition create pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 --resource-group sc-74e1434b-b435-587e-9dea-fa067deec898 SUCCESS: Description: New resource definition 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' created. Details: Resource definition 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' UUID is: 772692e2-3fca-4069-92e9-2bef22c68a6f jonathon@jonathon-framework:~$ linstor --controller new-xostor-server-01 volume-definition create pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 21483225088B --storage-pool xcp-sr-linstor_group_thin_device SUCCESS: Successfully set property key(s): StorPoolName SUCCESS: New volume definition with number '0' of resource definition 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' created. jonathon@jonathon-framework:~$ linstor --controller new-xostor-server-01 resource create --storage-pool xcp-sr-linstor_group_thin_device --providers LVM_THIN new-xostor-server-01 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 SUCCESS: Successfully set property key(s): StorPoolName INFO: Updated pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 DRBD auto verify algorithm to 'crct10dif-pclmul' SUCCESS: Description: New resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on node 'new-xostor-server-01' registered. Details: Resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on node 'new-xostor-server-01' UUID is: 3072aaae-4a34-453e-bdc6-facb47809b3d SUCCESS: Description: Volume with number '0' on resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on node 'new-xostor-server-01' successfully registered Details: Volume UUID is: 52b11ef6-ec50-42fb-8710-1d3f8c15c657 SUCCESS: Created resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-01' jonathon@jonathon-framework:~$ linstor --controller new-xostor-server-01 resource create --auto-place +1 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 SUCCESS: Successfully set property key(s): StorPoolName SUCCESS: Successfully set property key(s): StorPoolName SUCCESS: Description: Resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' successfully autoplaced on 2 nodes Details: Used nodes (storage pool name): 'new-xostor-server-02 (xcp-sr-linstor_group_thin_device)', 'new-xostor-server-03 (xcp-sr-linstor_group_thin_device)' INFO: Resource-definition property 'DrbdOptions/Resource/quorum' updated from 'off' to 'majority' by auto-quorum INFO: Resource-definition property 'DrbdOptions/Resource/on-no-quorum' updated from 'off' to 'suspend-io' by auto-quorum SUCCESS: Added peer(s) 'new-xostor-server-02', 'new-xostor-server-03' to resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-01' SUCCESS: Created resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-02' SUCCESS: Created resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-03' SUCCESS: Description: Resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-03' ready Details: Auto-placing resource: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 SUCCESS: Description: Resource 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' on 'new-xostor-server-02' ready Details: Auto-placing resource: pvc-96cbebbe-f827-4a47-ae95-38b078e0d584At this point
jonathon@jonathon-framework:~$ linstor --controller new-xostor-server-01 v l | grep -e 'pvc-96cbebbe-f827-4a47-ae95-38b078e0d584' | new-xostor-server-01 | pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 | xcp-sr-linstor_group_thin_device | 0 | 1032 | /dev/drbd1032 | 9.20 GiB | Unused | UpToDate | | new-xostor-server-02 | pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 | xcp-sr-linstor_group_thin_device | 0 | 1032 | /dev/drbd1032 | 112.73 MiB | Unused | UpToDate | | new-xostor-server-03 | pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 | xcp-sr-linstor_group_thin_device | 0 | 1032 | /dev/drbd1032 | 112.73 MiB | Unused | UpToDate |To force the sync, run the following command on the node with the data
drbdadm invalidate-remote pvc-96cbebbe-f827-4a47-ae95-38b078e0d584This will kick it to get the data re-synced.
[14:51 new-xostor-server-01 ~]# drbdadm invalidate-remote pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 [14:51 new-xostor-server-01 ~]# drbdadm status pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 role:Secondary disk:UpToDate new-xostor-server-02 role:Secondary replication:SyncSource peer-disk:Inconsistent done:1.14 new-xostor-server-03 role:Secondary replication:SyncSource peer-disk:Inconsistent done:1.18 [14:51 new-xostor-server-01 ~]# drbdadm status pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 pvc-96cbebbe-f827-4a47-ae95-38b078e0d584 role:Secondary disk:UpToDate new-xostor-server-02 role:Secondary peer-disk:UpToDate new-xostor-server-03 role:Secondary peer-disk:UpToDateSee: https://github.com/LINBIT/linstor-server/issues/389
Replica-1setup
# PV: pvc-6408a214-6def-44c4-8d9a-bebb67be5510 # S: pgdata-snapshot # s: 10741612544B #get size lvs --noheadings --units B -o lv_size linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 #prep lvcreate -V 10741612544B --thinpool linstor_group/thin_device -n pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 linstor_group #create snapshot linstor --controller original-xostor-server s create pvc-6408a214-6def-44c4-8d9a-bebb67be5510 pgdata-snapshot #send thin_send linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000_pgdata-snapshot 2>/dev/null | ssh root@new-xostor-server-01 thin_recv linstor_group/pvc-6408a214-6def-44c4-8d9a-bebb67be5510_00000 2>/dev/null # 1 linstor --controller new-xostor-server-01 resource-definition create pvc-6408a214-6def-44c4-8d9a-bebb67be5510 --resource-group sc-b066e430-6206-5588-a490-cc91ecef53d6 linstor --controller new-xostor-server-01 volume-definition create pvc-6408a214-6def-44c4-8d9a-bebb67be5510 10741612544B --storage-pool xcp-sr-linstor_group_thin_device linstor --controller new-xostor-server-01 resource create new-xostor-server-01 pvc-6408a214-6def-44c4-8d9a-bebb67be5510--- apiVersion: v1 kind: PersistentVolume metadata: name: pvc-6408a214-6def-44c4-8d9a-bebb67be5510 annotations: pv.kubernetes.io/provisioned-by: linstor.csi.linbit.com finalizers: - external-provisioner.volume.kubernetes.io/finalizer - kubernetes.io/pv-protection - external-attacher/linstor-csi-linbit-com spec: accessModes: - ReadWriteOnce capacity: storage: 10Gi # Ensure this matches the actual size of the LINSTOR volume persistentVolumeReclaimPolicy: Retain storageClassName: linstor-replica-one-local # Adjust to the storage class you want to use volumeMode: Filesystem csi: driver: linstor.csi.linbit.com fsType: ext4 volumeHandle: pvc-6408a214-6def-44c4-8d9a-bebb67be5510 volumeAttributes: linstor.csi.linbit.com/mount-options: '' linstor.csi.linbit.com/post-mount-xfs-opts: '' linstor.csi.linbit.com/uses-volume-context: 'true' linstor.csi.linbit.com/remote-access-policy: | - fromSame: - xcp-ng/node nodeAffinity: required: nodeSelectorTerms: - matchExpressions: - key: xcp-ng/node operator: In values: - new-xostor-server-01 --- apiVersion: v1 kind: PersistentVolumeClaim metadata: annotations: pv.kubernetes.io/bind-completed: 'yes' pv.kubernetes.io/bound-by-controller: 'yes' volume.beta.kubernetes.io/storage-provisioner: linstor.csi.linbit.com volume.kubernetes.io/selected-node: ovbh-vtest-k8s01-worker01 volume.kubernetes.io/storage-provisioner: linstor.csi.linbit.com finalizers: - kubernetes.io/pvc-protection name: acid-merch-2 namespace: default spec: accessModes: - ReadWriteOnce resources: requests: storage: 10Gi storageClassName: linstor-replica-one-local volumeMode: Filesystem volumeName: pvc-6408a214-6def-44c4-8d9a-bebb67be5510 -
Last week I stood up two XCP-ng hosts with LINSTOR without issue.
This week I am standing up a third XCP-ng host and encounter a show stopping error when I try to install LINSTOR:
Error: Package: xcp-ng-linstor-1.1-3.xcpng8.2.noarch (xcp-ng-linstor)
Requires: sm-linstor
...
Failed to install LINSTOR package: xcp-ng-linstor.This third host is 100% identical in hardware to the first two hosts. Fresh from-scratch new install of XCP-ng. Here is an output of commands and their results on the third host:
[21:35 bol-xcp3 ~]# wget https://gist.githubusercontent.com/Wescoeur/7bb568c0e09e796710b0ea966882fcac/raw/052b3dfff9c06b1765e51d8de72c90f2f90f475b/gistfile1.txt -O install && chmod +x install --2024-11-16 21:35:08-- https://gist.githubusercontent.com/Wescoeur/7bb568c0e09e796710b0ea966882fcac/raw/052b3dfff9c06b1765e51d8de72c90f2f90f475b/gistfile1.txt Resolving gist.githubusercontent.com (gist.githubusercontent.com)... 185.199.111.133, 185.199.110.133, 185.199.109.133, ... Connecting to gist.githubusercontent.com (gist.githubusercontent.com)|185.199.111.133|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 3596 (3.5K) [text/plain] Saving to: ‘install’ 100%[=============================================================================>] 3,596 --.-K/s in 0s 2024-11-16 21:35:08 (22.4 MB/s) - ‘install’ saved [3596/3596] [21:35 bol-xcp3 ~]# ./install --disks /dev/nvme0n1 --thin Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile Excluding mirror: updates.xcp-ng.org * xcp-ng-base: mirrors.xcp-ng.org Excluding mirror: updates.xcp-ng.org * xcp-ng-updates: mirrors.xcp-ng.org Resolving Dependencies --> Running transaction check ---> Package xcp-ng-release-linstor.noarch 0:1.3-1.xcpng8.2 will be installed --> Finished Dependency Resolution Dependencies Resolved ======================================================================================================================= Package Arch Version Repository Size ======================================================================================================================= Installing: xcp-ng-release-linstor noarch 1.3-1.xcpng8.2 xcp-ng-updates 4.0 k Transaction Summary ======================================================================================================================= Install 1 Package Total download size: 4.0 k Installed size: 477 Downloading packages: xcp-ng-release-linstor-1.3-1.xcpng8.2.noarch.rpm | 4.0 kB 00:00:01 Running transaction check Running transaction test Transaction test succeeded Running transaction Installing : xcp-ng-release-linstor-1.3-1.xcpng8.2.noarch 1/1 Verifying : xcp-ng-release-linstor-1.3-1.xcpng8.2.noarch 1/1 Installed: xcp-ng-release-linstor.noarch 0:1.3-1.xcpng8.2 Complete! Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile Excluding mirror: updates.xcp-ng.org * xcp-ng-base: mirrors.xcp-ng.org Excluding mirror: updates.xcp-ng.org * xcp-ng-updates: mirrors.xcp-ng.org Resolving Dependencies --> Running transaction check ---> Package xcp-ng-linstor.noarch 0:1.1-3.xcpng8.2 will be installed --> Processing Dependency: sm-linstor for package: xcp-ng-linstor-1.1-3.xcpng8.2.noarch --> Finished Dependency Resolution Error: Package: xcp-ng-linstor-1.1-3.xcpng8.2.noarch (xcp-ng-linstor) Requires: sm-linstor Available: sm-2.30.8-2.1.0.linstor.4.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-2.1.0.linstor.5.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-2.1.0.linstor.6.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-2.3.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-2.3.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-7.1.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-10.1.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-10.1.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-10.1.0.linstor.3.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-12.1.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-12.1.0.linstor.3.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Available: sm-2.30.8-12.1.0.linstor.4.xcpng8.2.x86_64 (xcp-ng-linstor) sm-linstor Installed: sm-2.30.8-13.1.xcpng8.2.x86_64 (@xcp-ng-updates) Not found Available: sm-2.29.1-1.2.xcpng8.2.x86_64 (xcp-ng-base) Not found Available: sm-2.30.4-1.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.4-1.1.0.linstor.8.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.6-1.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.6-1.1.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.6-1.2.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.1.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.2.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.3.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.7-1.3.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.3.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.3.0.linstor.3.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.3.0.linstor.7.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.7-1.3.0.linstor.8.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.8-2.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.8-2.1.0.linstor.1.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.8-2.1.0.linstor.2.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.8-2.1.0.linstor.3.xcpng8.2.x86_64 (xcp-ng-linstor) Not found Available: sm-2.30.8-2.3.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.8-7.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.8-10.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found Available: sm-2.30.8-12.1.xcpng8.2.x86_64 (xcp-ng-updates) Not found You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest Failed to install LINSTOR package: xcp-ng-linstor.It seems the sm* package(s) are missing ? I don't know what to do.
Edit 2024-11-17 1702 CST:
yum install xcp-ng-release-linstorindicatesxcp-ng-release-linstoris already installed and latest version.[16:14 bol-xcp3 ~]# yum install xcp-ng-release-linstor Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile Excluding mirror: updates.xcp-ng.org * xcp-ng-base: mirrors.xcp-ng.org Excluding mirror: updates.xcp-ng.org * xcp-ng-updates: mirrors.xcp-ng.org Package xcp-ng-release-linstor-1.3-1.xcpng8.2.noarch already installed and latest version Nothing to do -
@BlueToast This should be fixed now. Please retry the XOSTOR installation.
-
@Danp Success this this - thanks for the assist.
Executed with great success:yum install xcp-ng-linstor yum install xcp-ng-release-linstor ./install --disks /dev/nvme0n1 --thin
